Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 2 Sensor Type) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0076583 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 2 Sensor Type) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 2 Sensor Type)  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU assembly receives the reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E222388E30
5.51,1.385 6.708,2.031 1.198,0.646 10 Clearance Warning ECU Assembly 3.292,1.094 4.594,1.781 1.302,0.688 10 Park/Neutral Position Switch Assembly 5.552,0.615 6.146,0.823 0.594,0.208 10 RL 5.51,1.219 6.104,1.427 0.594,0.208 10 I82 3.292,0.948 3.604,1.177 0.313,0.229 10 E4 2.25,0.875 3,1.146 0.75,0.271 10 BKUP LP 0.323,0.594 1.781,1 1.458,0.406 10 from IG1 NO. 1 Relay 5.281,0.49 5.469,0.688 0.188,0.198 10 27 3.542,0.531 3.823,0.781 0.281,0.25 10 RB 4.313,0.521 4.531,0.667 0.219,0.146 10 RL 3.385,0.531 3.521,0.729 0.135,0.198 10 1 4.594,0.521 4.76,0.729 0.167,0.208 10 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the I82 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I82-27 (RL) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V
I82-27 (RL) - Body ground Ignition switch ON
Shift lever in any position except R
Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the E4 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I82-27 (RL) - E4-2 (RL) Always Below 1 Ω
I82-27 (RL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E4-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR