WARNING LIGHT INITIAL CHECK
Release the parking brake.
Before releasing the parking brake, set the chocks to hold the vehicle for safety.
When the parking brake is applied or the brake fluid level is low, the brake warning light comes on.
When the ignition switch is turned to ON, check that the ABS warning and brake warning lights all come on for approximately 3 seconds.
If the skid control ECU stores a DTC, the ABS warning light will come on.
If any of the indicators remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using the Intelligent Tester)
DTCs are stored if any malfunctions are detected during the check of each sensor.
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Switch the skid control ECU to Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
| Tester Display |
|---|
| Signal Check |
Check that the ABS warning light comes on for several seconds and then blink in the Test Mode pattern.
If the ABS warning light does not blink, inspect the ABS warning light circuit.
Check the ABS sensor.
Check that the ABS warning light is blinking in the Test Mode pattern before performing the following ABS sensor check.
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.
The sensor check may not complete if wheelspin occurs.
The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel or spinning the wheels.
After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again.
Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
Check that the ABS warning light goes off.
The ABS warning light goes off when the sensor check has completed.
The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.
Stop the vehicle.
When the sensor check has completed, the ABS warning light goes off while driving, and blinks in the Test Mode pattern while the vehicle is stopped.
If the sensor check has not completed, the ABS warning light will blink while driving and the ABS system will not operate.
End of Sensor Check
If the sensor checks have completed, the ABS warning light blinks in the Test Mode pattern when the vehicle stops and the ABS warning light goes off while the vehicle is being driven.
If the sensor checks have not completed, the ABS warning light will blink while driving and the ABS system will not operate.
Reading Sensor Check DTCs
Read the DTC(s) by following the intelligent tester screen.
If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.
If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform Test Mode inspection again.
See "Sensor Check DTCs".
Turn the ignition switch off and disconnect the intelligent tester.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| C1271 | Low Output Signal of Front Speed Sensor RH | ·
Front speed sensor RH ·
Sensor installation ·
Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| C1272 | Low Output Signal of Front Speed Sensor LH | ·
Front speed sensor LH ·
Sensor installation ·
Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| C1273 | Low Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH ·
Sensor installation ·
Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| C1274 | Low Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH ·
Sensor installation ·
Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
The codes in this table are output only in Test Mode (signal check).
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using the Intelligent Tester)
DTCs are stored if any malfunctions are detected during the check of each sensor.
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P.
| *a | Front view of DLC3 |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch to ON.
Check that the ABS warning light comes on for several seconds and then blink in the Test Mode pattern.
If the ABS warning light does not blink, inspect the TS and CG terminal circuit and ABS warning light circuit.
Check the ABS sensor.
Check that the ABS warning light is blinking in the Test Mode pattern before performing the following ABS sensor check.
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.
The sensor check may not complete if wheelspin occurs.
The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel or spinning the wheels.
After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again.
Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
Check that the ABS warning light goes off.
The ABS warning light goes off when the sensor check has completed.
The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.
Stop the vehicle.
When the sensor check has completed, the ABS warning light goes off while driving, and blinks in the Test Mode pattern while the vehicle is stopped.
If the sensor checks have not completed, the ABS warning light will blink while driving and the ABS system will not operate.
End of Sensor Check
If the sensor checks have completed, the ABS warning light blinks in the Test Mode pattern when the vehicle stops and the ABS warning light goes off while the vehicle is being driven.
If the sensor checks have not completed, the ABS warning light will blink while driving and the ABS system will not operate.
Reading Sensor Check DTCs
| *a | Front view of DLC3 |
Using SST, connect terminals TC and CG of the DLC3.
Count the number of blinks of the ABS warning light.
How to read DTCs:
Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.
If one code is detected:
The light repeats the same code after a pause of 4 seconds.
If multiple codes are detected:
The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.
If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.
If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform Test Mode inspection again.
If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.
See "Sensor Check DTCs".
After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3, and turn the ignition switch off.
Turn the ignition switch to ON to cancel Test Mode.
If the ignition switch is not turned off and back to ON after SST is removed from the DLC3, the previous Test Mode will continue.
If the ignition switch is turned back to ON with terminals TS and CG shorted, the previous Test Mode will continue.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| 71 | Low Output Signal of Front Speed Sensor RH | ·
Front speed sensor RH ·
Sensor installation ·
Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| 72 | Low Output Signal of Front Speed Sensor LH | ·
Front speed sensor LH ·
Sensor installation ·
Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| 73 | Low Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH ·
Sensor installation ·
Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| 74 | Low Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH ·
Sensor installation ·
Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| 75 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| 76 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| 77 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| 78 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
The DTCs in this table are output only in Test Mode (signal check).