When using a vise, do not overtighten it.
Do not drop the power steering ECU with motor assembly, strike it with tools or subject it to impacts.
If the power steering ECU with motor assembly is subjected to an impact, replace it with a new one.
Do not pull the wire harness of the electric power steering column sub-assembly.
Do not allow any moisture to come into contact with the power steering ECU with motor assembly.
Do not loosen any bolts not mentioned in the procedure.
84450
1.INSTALL IGNITION OR STARTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)
Engage the 2 claws to install the ignition or starter switch assembly to the steering column upper bracket assembly.
2.INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Smart Entry and Start System)
| *a | LOCK |
| *b | ACC |
Make sure that the ignition switch lock cylinder assembly is in the ACC position.
Install the ignition switch lock cylinder assembly to the steering column upper bracket assembly.
Make sure that the ignition switch lock cylinder assembly is securely installed.
85432
3.INSTALL KEY INTERLOCK SOLENOID (w/o Smart Entry and Start System)
Engage the claw to install the key interlock solenoid to the steering column upper bracket assembly.
Install the screw.
84052
4.INSTALL UNLOCK WARNING SWITCH ASSEMBLY (w/o Smart Entry and Start System)
Slide the unlock warning switch assembly and engage the 2 claws to install the unlock warning switch assembly to the steering column upper bracket assembly as shown in the illustration.
89783
5.INSTALL TRANSPONDER KEY AMPLIFIER (w/o Smart Entry and Start System)
Align the transponder key amplifier with the steering column upper bracket assembly. Tilt the transponder key amplifier slightly and slide it into position.
Push the transponder key amplifier, and engage the 2 claws to install the transponder key amplifier to the steering column upper bracket assembly.
6.INSPECT STEERING LOCK OPERATION (w/o Smart Entry and Start System)
89650
7.INSTALL POWER STEERING ECU ASSEMBLY
8.INSTALL POWER STEERING ECU WITH MOTOR ASSEMBLY
| *1 | Service Nut |
Install the 2 service nuts to the steering main shaft.
12.0 mm (0.472 in.)
1.25 mm (0.0492 in.)
Simultaneously to rotate the service nut that was installed first counterclockwise and rotate the service nut that was installed second clockwise to lock them.
Do not apply excess torque to the service nuts by using a tool such as an impact wrench.
These nuts are installed to turn the steering main shaft. They should be removed after inspecting the steering main shaft rotating torque.
Install a new O-ring to the power steering ECU with motor assembly.
Apply grease to the splines of the power steering ECU with motor assembly.
First wipe off the existing grease from the splines, and then apply the dedicated grease supplied with a new power steering motor assembly or electric power steering column sub-assembly.
Insert the power steering ECU with motor assembly into the splines of the electric power steering column sub-assembly.
Do not damage the gears.
| *1 | Aluminum Plate |
| *2 | Wooden Block |
Secure the steering column assembly in a vice using aluminum plates and wooden block as shown in the illustration.
Do not overtighten the vice, as the steering column assembly may become deformed.
Secure the steering column assembly so that power steering motor assembly is directly upright.
Support the steering column assembly with a wooden block or similar item to ensure that it does not fall.
Temporarily install the power steering ECU with motor assembly to the electric power steering column sub-assembly with 2 new bolts while rotating the steering main shaft at approximately 4 rpm.
When temporarily installing the 2 bolts to the power steering motor assembly, do not tighten them all the way down.
Rotate the steering main shaft 120 to 240 degrees at approximately 4 rpm.
Rotate the steering main shaft 180 degrees clockwise and counterclockwise at approximately 4 rpm and repeat this operation 2 or 3 times to align the power steering ECU with motor assembly.
Tighten the 2 bolts.
Make sure not to move the power steering motor assembly after adjusting the axis.
Measure the turning torque of the steering main shaft.
Ensure that there is no abnormal resistance during rotation.
If the torque is not as specified, readjust the axis of the power steering ECU with motor assembly.
Remove the 2 service nuts from the steering main shaft.
Connect the 2 connectors to the power steering ECU assembly.
F1901
9.INSTALL ECU WIRE SUB-ASSEMBLY
Engage the 2 wire harness clamps to install a new ECU wire sub-assembly.
Connect the 2 connectors to the power steering ECU with motor assembly.
8965A
10.INSTALL POWER STEERING ECU PROTECTOR
Engage the 2 claws to install a new power steering ECU protector to the power steering ECU with motor assembly.
11.INSTALL STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (w/o Smart Entry and Start System)
Secure the steering column assembly in a vise.
Temporarily install the steering column upper with switch bracket assembly to the steering column assembly with 2 new tapered-head bolts.
Tighten the 2 tapered-head bolts until the bolt heads break off.
45020A
12.INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Entry and Start System)
When replacing the steering lock actuator assembly, refer to Service Bulletin.
Secure the steering column assembly in a vise.
Temporarily install the steering lock actuator assembly to the steering column assembly with 2 new tapered-head bolts.
Tighten the 2 tapered-head bolts until the bolt heads break off.