Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2013.07–2014.05
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0073985 DIFFERENTIAL CASE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL DIFFERENTIAL SIDE GEAR

a.
C138528

Coat the 2 front differential side gears, 2 No. 1 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.


Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C138706

Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


Hide 3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C138707

Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin.

NOTICE:

Align the holes, and install the front differential pinion shaft straight pin.



b.
C138711

Using a chisel and hammer, stake the differential case.

NOTICE:

Stake the differential case after adjusting the backlash.



Hide 41311F 5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C201521
2.458,0.592 2.768,0.735 0.31,0.143 10 SST 1.87,0.803 2.406,0.689 2.406,0.689 1.887,1.007 false 1.747,0.661 2.406,0.689 false

Using SST and a press, install a new front differential case rear tapered roller bearing to the differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:

Do not damage the bearing cage during bearing inner race installation.



b.
C138714
1.333,1.167 0.406,1.75 0.406,1.75 1.146,1.542 false 0.125,1.698 0.448,1.865 0.323,0.167 10 SST

Using SST and a hammer, install a new front differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the front differential case rear tapered roller bearing (outer race) and transaxle case sub-assembly.



Hide 41311E 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C274853
1.771,0.302 2.427,0.302 2.427,0.302 1.865,0.75 false 1.865,0.479 2.427,0.302 false 2.469,0.229 2.927,0.427 0.458,0.198 10 SST

Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.

SST
09523-36010  
09950-60010  (09951-00540)
09950-70010  (09951-07100)

NOTICE:

Do not damage the bearing cage during bearing inner race installation.



b.
C138715
1.854,1.104 2.625,1.521 2.625,1.521 1.948,1.438 false 2.698,1.448 3.063,1.719 0.365,0.271 10 false SST

Install the shim to the transaxle housing.


c.

Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle housing.



Hide 7.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove the seal packing from the contact surfaces between the transaxle housing and transaxle case sub-assembly.


b.
C205239

Install the differential assembly to the transaxle case sub-assembly.


c.
C274854
1.406,1.854 1.563,2.052 0.156,0.198 10 A 1.792,1.917 1.948,2.115 0.156,0.198 10 A 2.115,1.938 2.271,2.135 0.156,0.198 10 A

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt A : 23 N*m (231 kgf*cm, 17 ft.*lbf)
except Bolt A : 31 N*m (312 kgf*cm, 22 ft.*lbf)


d.
C138262
1.083,3.323 0.938,4.115 false 0.802,4.156 1.219,4.396 0.417,0.24 10 false SST

Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.

SST
09564-33010  

Turning torque:

1.3 to 1.7 N*m (14 to 17 kgf*cm, 12 to 15 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness: mm (in.)
Thickness Thickness Thickness Thickness
2.000 (0.0787) 2.225 (0.0876) 2.450 (0.0965) 2.675 (0.105)
2.025 (0.0797) 2.250 (0.0886) 2.475 (0.0974) 2.700 (0.106)
2.050 (0.0807) 2.275 (0.0896) 2.500 (0.0984) 2.725 (0.107)
2.075 (0.0817) 2.300 (0.0906) 2.525 (0.0994) 2.750 (0.108)
2.100 (0.0827) 2.325 (0.0915) 2.550 (0.100) 2.775 (0.109)
2.125 (0.0837) 2.350 (0.0925) 2.575 (0.101) 2.800 (0.110)
2.150 (0.0846) 2.375 (0.0935) 2.600 (0.102) 2.825 (0.111)
2.175 (0.0856) 2.400 (0.0945) 2.625 (0.103) 2.850 (0.112)
2.200 (0.0866) 2.425 (0.0955) 2.650 (0.104) 2.875 (0.113)


e.
C205232

Remove the 20 bolts and the transaxle housing from the transaxle case sub-assembly.


f.
C205239

Remove the differential case from the transaxle case sub-assembly.


Hide 41221 8.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215
1.385,0.083 1.719,0.365 0.333,0.281 10 false *a
*a 90 to 110°C


Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the ring gear to more than 110°C (230°F).



b.
C138531
1.26,1.438 0.552,0.969 0.552,0.969 1.177,1.5 false 0.354,0.854 0.635,1.063 0.281,0.208 10 false *a
*a Matchmark


Clean the contact surface of the differential case.


c.

Align the matchmarks, set the front differential ring gear to the differential case.


d.
C138532

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 88 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.




Hide 31105H 9.INSTALL TRANSAXLE CASE OIL SEAL

a.
C205332
0.178,2.31 0.496,2.466 0.319,0.156 10 SST 2.908,1.412 3.226,1.568 0.319,0.156 10 SST 1.452,1.212 0.548,2.378 0.548,2.378 1.415,1.504 false 1.963,1.894 2.876,1.537 2.876,1.537 2.415,1.93 false

Coat the lip of a new transaxle case oil seal with a small amount of MP grease.


b.

Using SST and a hammer, install the transaxle case oil seal.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the transaxle case oil seal is installed in the correct direction.



Hide 31105D 10.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C205333
3.006,1.343 3.298,1.494 0.292,0.151 10 SST 1.128,0.887 2.971,1.433 2.971,1.433 2.47,1.916 false

Coat the lip of a new front transaxle case oil seal with a small amount of MP grease.


b.

Using SST and a hammer, install the front transaxle case oil seal.

SST
09308-14010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the front transaxle case oil seal is installed in the correct direction.