Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › from 2013.07
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073930 REAR CRANKSHAFT OIL SEAL A

2AR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Apply MP grease to the lip of a new oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the oil seal.

·

Do not allow MP grease to contact the dust seal.




b.
A195810
1.292,1.354 1.99,1.927 true 2,1.927 1.854,1.188 true 2.073,1.875 2.479,2.052 0.406,0.177 10 SST

Using SST and a hammer, tap in the oil seal until its surface is flush with the edges of the cylinder block and crankcase.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Keep the lip of the oil seal free from foreign matter.

·

Do not tap in the oil seal at an angle.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A195875
1.375,1.26 0.854,1.26 false 1.292,0.781 1.146,0.781 1.146,0.781 1.146,1.26 false 0.49,1.177 0.823,1.333 0.333,0.156 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



b.

Clean the bolts and their installation holes.


c.
A196850

Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



d.
A196851
2.354,0.979 2.198,0.688 false 1.854,2 1.708,1.708 false 2.385,1.021 2.563,1.188 0.177,0.167 10 false *2 1.865,2.031 2.042,2.198 0.177,0.167 10 false *1
*1 Drive Plate
*2 Rear Drive Plate Spacer
V100135

Transaxle Side


Install the drive plate and rear drive plate spacer onto the crankshaft.


e.
A192239C51
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A196849
1.938,0.333 2.031,0.49 0.094,0.156 10 true 1 1.938,1.719 2.031,1.896 0.094,0.177 10 true 2 1.281,1.052 1.396,1.198 0.115,0.146 10 true 3 2.656,1.042 2.75,1.198 0.094,0.156 10 true 4 1.469,0.552 1.583,0.698 0.115,0.146 10 true 5 2.438,1.521 2.552,1.677 0.115,0.156 10 true 6 2.417,0.552 2.542,0.708 0.125,0.156 10 true 7 1.469,1.531 1.563,1.677 0.094,0.146 10 true 8

Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.