Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2014.05–2015.04
RM19V0EQ _59 Vehicle Exterior _014620 WIPER / WASHER _0074239 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Speed Signal Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a vehicle speed signal from the combination meter assembly to control the automatic windshield wiper system.

A voltage of 12 V or 5 V is output from the combination meter assembly and then input to the skid control ECU.

A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly.

Each ECU controls the respective system based on the pulse signal.

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

WIRING DIAGRAM

E230186E05
0.177,1.552 1.583,1.854 1.406,0.302 10 false Skid Control ECU 0.865,0.583 1.354,0.875 0.49,0.292 10 false SP1 0.177,1.406 0.656,1.844 0.479,0.438 10 false A49 1.208,0.583 1.604,0.979 0.396,0.396 10 false 2 0.115,2.76 3.198,2.927 3.083,0.167 10 false Certification ECU (Smart Key ECU Assembly)*5 0.115,2.615 0.542,2.833 0.427,0.219 10 false I78 0.354,7.333 0.781,7.635 0.427,0.302 10 false I72 0.354,7.49 2.667,7.813 2.313,0.323 10 false Windshield Wiper Relay Assembly*4 1.719,7.188 2.198,7.365 0.479,0.177 10 false SPD 1.74,2.333 2.521,2.594 0.781,0.26 10 false SPD 2.104,2.333 2.438,2.594 0.333,0.26 10 false 27 2.927,2.333 3.333,2.635 0.406,0.302 10 false 19 3.938,2.333 4.24,2.667 0.302,0.333 10 false 18 2.927,3.75 3.323,4.052 0.396,0.302 10 false 20 3.938,3.75 4.281,4.083 0.344,0.333 10 false 17 2.104,7.083 2.406,7.323 0.302,0.24 10 false 24 3.948,7.083 4.177,7.271 0.229,0.188 10 false 16 2.917,7.083 3.198,7.313 0.281,0.229 10 false 21 5.354,7.094 5.646,7.292 0.292,0.198 10 false 57 5.292,5.104 5.646,5.375 0.354,0.271 10 false 17 5.417,0.563 5.719,0.708 0.302,0.146 10 false 8 5.417,2.344 5.688,2.49 0.271,0.146 10 false 9 5.604,0.677 5.885,0.979 0.281,0.302 10 false SI 5.594,2.438 5.948,2.667 0.354,0.229 10 false +S 5.281,2.698 5.615,2.844 0.333,0.146 10 false I18 5.281,2.844 7.115,3.042 1.833,0.198 10 false Combination Meter Assembly 5.781,7.479 6.063,7.635 0.281,0.156 10 false A25 6.104,7.479 6.51,7.656 0.406,0.177 10 false ECM 4.406,5.635 6.99,6 2.583,0.365 10 false Navigation ECU Sub-assembly*2 or Radio and Display Receiver Assembly*3 2.354,8.24 4.75,8.406 2.396,0.167 10 false *5: w/ Smart Entry and Start System 0.313,8.24 2.229,8.563 1.917,0.323 10 false *4: w/ Auto Wiper System 4.802,7.906 6.708,8.083 1.906,0.177 10 false *3: for Radio and Display Type 5.594,7.094 6.063,7.333 0.469,0.24 10 false SPD 5.583,5.198 5.917,5.344 0.333,0.146 10 false SPD 5.583,3.771 6.063,4.031 0.479,0.26 10 false SPD 5.24,5.281 5.75,5.583 0.51,0.302 10 false I155 5.302,5.469 5.604,5.656 0.302,0.188 10 false *3 4.938,5.104 5.26,5.354 0.323,0.25 10 false 17 4.927,5.281 5.26,5.531 0.333,0.25 10 false I67 4.948,5.469 5.24,5.688 0.292,0.219 10 false *2 2.115,3.76 2.427,3.927 0.313,0.167 10 false 11 0.323,4.104 0.667,4.323 0.344,0.219 10 false I69 5.344,3.771 5.698,3.979 0.354,0.208 10 false 17 5.156,4.042 5.698,4.198 0.542,0.156 10 false I150 0.313,4.26 3.031,4.583 2.719,0.323 10 false Stereo Component Amplifier Assembly*2 5.156,4.177 6.906,4.354 1.75,0.177 10 false Radio Receiver Assembly*1 1.719,3.865 2.24,4.135 0.521,0.271 10 false SPD 2.438,7.917 4.479,8.094 2.042,0.177 10 false *2: for Navigation Receiver Type 0.313,7.917 2.104,8.083 1.792,0.167 10 false *1: for Radio Receiver Type 3.094,7.49 4.313,7.656 1.219,0.167 10 false Junction Connector 2.781,7.49 3.333,7.698 0.552,0.208 10 false I124

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (SPEED SENSOR SIGNAL)
a.
E277112C01
1.5,0.354 1.854,0.604 0.354,0.25 1.156,2.135 1.396,1.406 false 2.802,3.646 3.26,3.844 0.458,0.198 10 false GND 1.042,3.906 1.5,4.104 0.458,0.198 10 false (A) 1.604,0.396 2.063,0.594 0.458,0.198 10 false I18 0.24,0.208 0.698,0.406 0.458,0.198 10 false *a 1.021,2.167 1.563,2.521 0.542,0.354 10 false +S
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I18-9 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I72 windshield wiper relay assembly connector and I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-24 (SPD) - I18-9 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I72 windshield wiper relay assembly connector and I124 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-24 (SPD) - I124-20 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR