Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.05–2015.04
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU which uses this information to create the vehicle speed sensor signal*a. The vehicle speed sensor signal consists of pulses sent to the combination meter assembly from the skid control ECU. To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on the pulse signal.

*a: This vehicle speed sensor signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E230186E05
0.177,1.552 1.583,1.854 1.406,0.302 10 false Skid Control ECU 0.865,0.583 1.354,0.875 0.49,0.292 10 false SP1 0.177,1.406 0.656,1.844 0.479,0.438 10 false A49 1.208,0.583 1.604,0.979 0.396,0.396 10 false 2 0.115,2.76 3.198,2.927 3.083,0.167 10 false Certification ECU (Smart Key ECU Assembly)*5 0.115,2.615 0.542,2.833 0.427,0.219 10 false I78 0.354,7.333 0.781,7.635 0.427,0.302 10 false I72 0.354,7.49 2.667,7.813 2.313,0.323 10 false Windshield Wiper Relay Assembly*4 1.719,7.188 2.198,7.365 0.479,0.177 10 false SPD 1.74,2.333 2.521,2.594 0.781,0.26 10 false SPD 2.104,2.333 2.438,2.594 0.333,0.26 10 false 27 2.927,2.333 3.333,2.635 0.406,0.302 10 false 19 3.938,2.333 4.24,2.667 0.302,0.333 10 false 18 2.927,3.75 3.323,4.052 0.396,0.302 10 false 20 3.938,3.75 4.281,4.083 0.344,0.333 10 false 17 2.104,7.083 2.406,7.323 0.302,0.24 10 false 24 3.948,7.083 4.177,7.271 0.229,0.188 10 false 16 2.917,7.083 3.198,7.313 0.281,0.229 10 false 21 5.354,7.094 5.646,7.292 0.292,0.198 10 false 57 5.292,5.104 5.646,5.375 0.354,0.271 10 false 17 5.417,0.563 5.719,0.708 0.302,0.146 10 false 8 5.417,2.344 5.688,2.49 0.271,0.146 10 false 9 5.604,0.677 5.885,0.979 0.281,0.302 10 false SI 5.594,2.438 5.948,2.667 0.354,0.229 10 false +S 5.281,2.698 5.615,2.844 0.333,0.146 10 false I18 5.281,2.844 7.115,3.042 1.833,0.198 10 false Combination Meter Assembly 5.781,7.479 6.063,7.635 0.281,0.156 10 false A25 6.104,7.479 6.51,7.656 0.406,0.177 10 false ECM 4.406,5.635 6.99,6 2.583,0.365 10 false Navigation ECU Sub-assembly*2 or Radio and Display Receiver Assembly*3 2.354,8.24 4.75,8.406 2.396,0.167 10 false *5: w/ Smart Entry and Start System 0.313,8.24 2.229,8.563 1.917,0.323 10 false *4: w/ Auto Wiper System 4.802,7.906 6.708,8.083 1.906,0.177 10 false *3: for Radio and Display Type 5.594,7.094 6.063,7.333 0.469,0.24 10 false SPD 5.583,5.198 5.917,5.344 0.333,0.146 10 false SPD 5.583,3.771 6.063,4.031 0.479,0.26 10 false SPD 5.24,5.281 5.75,5.583 0.51,0.302 10 false I155 5.302,5.469 5.604,5.656 0.302,0.188 10 false *3 4.938,5.104 5.26,5.354 0.323,0.25 10 false 17 4.927,5.281 5.26,5.531 0.333,0.25 10 false I67 4.948,5.469 5.24,5.688 0.292,0.219 10 false *2 2.115,3.76 2.427,3.927 0.313,0.167 10 false 11 0.323,4.104 0.667,4.323 0.344,0.219 10 false I69 5.344,3.771 5.698,3.979 0.354,0.208 10 false 17 5.156,4.042 5.698,4.198 0.542,0.156 10 false I150 0.313,4.26 3.031,4.583 2.719,0.323 10 false Stereo Component Amplifier Assembly*2 5.156,4.177 6.906,4.354 1.75,0.177 10 false Radio Receiver Assembly*1 1.719,3.865 2.24,4.135 0.521,0.271 10 false SPD 2.438,7.917 4.479,8.094 2.042,0.177 10 false *2: for Navigation Receiver Type 0.313,7.917 2.104,8.083 1.792,0.167 10 false *1: for Radio Receiver Type 3.094,7.49 4.313,7.656 1.219,0.167 10 false Junction Connector 2.781,7.49 3.333,7.698 0.552,0.208 10 false I124

PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.
E224284C16
0.313,1.635 0.771,1.917 0.458,0.281 1.969,1.906 1.969,0.677 1.969,0.677 2.167,0.677 false 0.115,0.073 0.396,0.354 0.281,0.281 10 false *a 2.208,0.583 2.75,0.771 0.542,0.188 10 false +S 0.448,1.688 0.771,1.854 0.323,0.167 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I18-9 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Reconnect the I18 combination meter assembly connector.


b.
C238832C13
1.479,0.604 1.938,0.885 0.458,0.281 1,1.948 1,2.604 false 0.156,0.146 0.708,0.49 0.552,0.344 10 false *a 0.875,2.625 1.563,3.01 0.688,0.385 10 false SP1 1.583,0.667 2.229,1.031 0.646,0.365 10 false A49
*a Front view of wire harness connector
(to Skid Control ECU)


Disconnect the A49 skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-2 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT SKID CONTROL ECU (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
3.INSPECT SKID CONTROL ECU (INPUT WAVEFORM)
a.
E262474C01
1.5,0.292 1.917,0.5 0.417,0.208 1.146,2.031 1.5,1.344 false 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 1.615,0.323 1.885,0.5 0.271,0.177 10 false I18 1.292,3.99 1.542,4.188 0.25,0.198 10 false A 2.927,3.698 3.333,3.906 0.406,0.208 10 false GND 1.042,2.063 1.417,2.26 0.375,0.198 10 false SI
*a Component with harness connected
(Combination Meter Assembly)


Check the input waveform.

i.

Reconnect the A49 skid control ECU connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal I18-8 (SI) and body ground.


iv.

Turn the ignition switch to ON.


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
a.

Disconnect the I18 combination meter assembly and A49 skid control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-2 (SP1) - I18-8 (SI) Always Below 1 Ω
A49-2 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I124 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-9 (+S) - I124-18 Always Below 1 Ω
I18-9 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)
a.

Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.

HINT:

If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.


i.

Disconnect the I124 junction connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I124-19 - Body ground Ignition switch ON 4.5 to 14 V
I124-20 - Body ground Ignition switch ON 4.5 to 14 V
I124-17 - Body ground Ignition switch ON 4.5 to 14 V
I124-16 - Body ground Ignition switch ON 4.5 to 14 V
I124-21 - Body ground Ignition switch ON 4.5 to 14 V




Result:
Result Proceed to
Voltage is not present in one circuit. A
Voltage is present in all the circuits. B



A

7.SYSTEM CHECK

B

REPLACE JUNCTION CONNECTOR (INSTRUMENT PANEL WIRE)

7.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in step 6.


Result:
Tester Connection System that uses the circuit Proceed to
I124-19 - Body ground Smart entry and start system*1 A
I124-20 - Body ground Audio/Visual system*2 B
I124-17 - Body ground Audio/Visual system*3, *4 or Navigation system*2 C
I124-16 - Body ground SFI system D
I124-21 - Body ground Wiper and washer system*5 E


*1: w/ Smart Entry and Start System

*2: for Navigation Receiver Type

*3: for Radio Receiver Type

*4: for Radio and Display Type

*5: for Auto Wiper System



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) CIRCUIT)

B

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY CIRCUIT)

C

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY CIRCUIT, NAVIGATION ECU SUB-ASSEMBLY CIRCUIT, RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT)

D

11.CHECK HARNESS AND CONNECTOR (ECM CIRCUIT)

E

12.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY CIRCUIT)
8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) CIRCUIT)
a.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-27 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY CIRCUIT)
a.

Disconnect the I69 stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-11 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY CIRCUIT, NAVIGATION ECU SUB-ASSEMBLY CIRCUIT, RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT)
a.

Disconnect the I150 radio receiver assembly*1 or I67 navigation ECU sub-assembly*2 or I155 radio and display receiver assembly*3 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-17 (SPD)*1 - Body ground Always 10 kΩ or higher
I67-17 (SPD)*2 - Body ground Always 10 kΩ or higher
I155-17 (SPD)*3 - Body ground Always 10 kΩ or higher


*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type



Result:
Result Proceed to
OK (for Radio Receiver Type) A
OK (for Navigation Receiver Type) B
OK (for Radio and Display Type) C
NG D



A

REPLACE RADIO RECEIVER ASSEMBLY

B

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ECM CIRCUIT)
a.

Disconnect the A25 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-57 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY CIRCUIT)
a.

Disconnect the I72 windshield wiper relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-24 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR