Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _034909 PRE-CRASH SAFETY _0163370 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A0A  Front Radar Sensor Region Code Mismatch  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on this information, the driving support ECU assembly sends pre-crash safety control operation signals.

When the millimeter wave radar sensor assembly is replaced with a new one, it acquires the country specification information from the driving support ECU assembly. Also, when the driving support ECU assembly is replaced with a new one, it receives country specification information from the main body ECU (multiplex network body ECU). When country specification information in the millimeter wave radar sensor assembly, driving support ECU assembly and/or main body ECU (multiplex network body ECU) do not match, DTC C1A0A is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A0A Front Radar Sensor Region Code Mismatch When the engine switch is on (IG), the country specification information from the driving support ECU assembly and millimeter wave radar sensor assembly do not match for 2.376 seconds.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Main body ECU (Multiplex network body ECU)



CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

Check that the millimeter wave radar sensor assembly has not been replaced with one from another vehicle.



PROCEDURE

1.CHECK FOR DTC (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



e.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

g.

Turn the engine switch off.


Result:
Result Proceed to
DTC C1A0A is output A
DTC C1A0A and other DTCs are output B



A

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCS (PRE-CRASH 2)
4.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A0A is not output A
DTC C1A0A is output B




A

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND DRIVING SUPPORT ECU ASSEMBLY