Home › Engine / Hybrid System › CRUISE CONTROL › MILLIMETER WAVE RADAR SENSOR › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0166364 MILLIMETER WAVE RADAR SENSOR N

CRUISE CONTROL  MILLIMETER WAVE RADAR SENSOR  ADJUSTMENT  


PROCEDURE

Hide 88211B 1.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

E247020C01
1.563,0.135 1.781,0.365 0.219,0.229 10 false *a 0.708,1.063 0.927,1.323 0.219,0.26 10 false *b
*a Approximately 10 m (32.8 ft.)
*b Approximately 14 m (45.9 ft.)


NOTICE:
·

Perform measurements on a level surface.

·

Make sure that no large pieces of metal are within a 10 m (32.8 ft.) x 14 m (45.9 ft.) area in front of the vehicle. If possible, the surrounding area should also be free of large metal objects.



a.

Before adjusting the radar beam axis, prepare the vehicle as follows.

i.

Check the tire pressure and adjust it if necessary.


ii.

Remove all excess weight from the vehicle (luggage, heavy objects, etc.).


iii.

Remove the cool air intake duct seal.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL



b.
E303313C01
1.604,0.917 2.031,0.5 false 2.083,0.417 2.396,0.573 0.313,0.156 10 false *a
*a Level


Check and adjust the vertical direction of the radar sensor.

i.

Remove dust, oil and foreign matter from the radar sensor's level rack.


ii.

Set a level on the radar sensor's level rack.


iii.
E300625C03
2.115,1.385 2.594,1.781 false 2.042,1.135 1.906,1.583 true 2.729,0.875 2.281,0.875 true 2.573,3.542 1.656,2.646 true 2.625,1.698 2.938,1.854 0.313,0.156 10 false *a 1.823,1.594 2.135,1.75 0.313,0.156 10 false *b 1.458,2.552 1.771,2.708 0.313,0.156 10 false *c 0.479,1.25 0.792,1.406 0.313,0.156 10 false *d 1.115,0.594 1.427,0.75 0.313,0.156 10 false *e 2.781,0.792 3.094,0.948 0.313,0.156 10 false *f
*a Level
*b Air Bubble
*c Bolt
*d Vehicle Front
*e Vehicle Left
*f 0°


Check that the level's air bubble is within the red frame.

OK:

Level's air bubble is within red frame.


If the bubble is not within the red frame, use a screwdriver to adjust the bolt until the air bubble is within the red frame.

HINT:
·

The adjustable range within the level's red frame is +/- 0.2°.

·

The target angle is +0.2° (upward angle of 0.2°).

Adjustment
Adjustment Direction Adjustment Procedure Adjustment Angle
Upward Turn screwdriver to positive (+) side When screwdriver is turned once, adjustment changes by about 0.12°.
Downward Turn screwdriver to negative (-) side





c.
E314796C01
0.323,0.917 1.083,0.781 1.083,0.781 0.583,1.427 false 1.719,1.333 2.135,0.917 true 1.125,0.719 1.583,0.917 0.458,0.198 10 false SST 2.177,0.813 2.49,1.01 0.313,0.198 10 false *1
*1 Millimeter Wave Radar Sensor


Adjust the reflector height.

i.

Adjust the reflector so that the center of SST (reflector) is the same height as the millimeter wave radar sensor.

SST
09870-60000  (09870-60010)
09870-60040  

HINT:

Prepare a 10 m (32.8 ft.) string, a string with a sharp-pointed weight (plumb bob), and a 5 m (16.4 ft.) tape measure.




d.

Place the reflector.

i.

Hang the string (with weight) from the center of the vehicle rear emblem. Mark the vehicle rear center point on the ground.

E310465C01
2.646,2.396 3.302,2.229 false 2.646,2.479 3.063,2.531 false 4.896,0.854 5.51,0.979 true 5.5,1.438 5.896,1.51 false 5.948,1.438 6.26,1.594 0.313,0.156 10 false *a 3.344,2.135 3.656,2.292 0.313,0.156 10 false *b 4.729,0.76 5.042,0.917 0.313,0.156 10 false *c 3.104,2.448 3.417,2.604 0.313,0.156 10 false *d
*a String *b Weight
*c Center point *d Mark



ii.

Repeat for the front of the vehicle.

E314795C01
1.552,0.844 2.208,0.583 true 1.552,1.5 1.948,1.542 false 3.375,2.135 4.031,2.292 false 3.583,2.448 4.031,2.375 false 2.021,1.458 2.333,1.615 0.313,0.156 10 false *a 3.208,2.042 3.521,2.198 0.313,0.156 10 false *b 2.25,0.49 2.563,0.646 0.313,0.156 10 false *c 3.427,2.365 3.74,2.521 0.313,0.156 10 false *d
*a String *b Weight
*c Center point *d Mark



iii.
E247024C01
1.719,1.094 1.313,0.917 false 0.458,0.208 0.708,0.427 0.25,0.219 10 false *a 1.115,0.792 1.365,1.01 0.25,0.219 10 false *b
*a Adjust center by moving string to right and left
*b Extend string through front center point


Set one end of the 10 m (32.8 ft.) string on the vehicle rear center point. Run the string over the vehicle front center point to a position 5 m (16.4 ft.) beyond the vehicle front center point, as shown in the illustration. Mark the 5 m (16.4 ft.) position.


iv.

Place the reflector (SST) at the marked position.

NOTICE:

Perform the operation as precisely as possible.


E310464C01
0.771,1.667 1.094,1.917 false 3.698,1.281 4.021,1.531 false 1.146,1.865 1.458,2.021 0.313,0.156 10 false *a 3.531,1.198 3.844,1.354 0.313,0.156 10 false *b 2.281,0.26 2.594,0.417 0.313,0.156 10 false *c 0.365,1.5 0.677,1.656 0.313,0.156 10 false *d
*a Reflector Placement Point *b Millimeter Wave Radar Sensor Position
*c 5000 mm (16.4 ft.) *d 11 mm (0.433 in.)




e.

Check the radar beam axis.

i.

When using the GTS:

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on and turn the cruise control system on using the cruise control switch.

4.

Enter the following menus: Powertrain / Radar Cruise / Utility.

5.

Follow the GTS display and continue with the adjustment.

CAUTION:

Do not come within 20 cm (7.87 in.) of the radar sensor.


NOTICE:
·

Turn the cruise control switch on before pressing "Next".

·

Make sure there is at least 20 cm (7.87 in.) between the millimeter wave radar sensor and any nearby individuals.

·

If "Error beam axis" is displayed on the screen, press the "Yes" button, and repeat again.

·

Check that there are no metal objects in the specified area in front of the vehicle (refer to the NOTICE at the beginning of this adjustment procedure).




Powertrain > Radar Cruise > Utility
Tester Display
Beam Axis Adjustment
50005 239 4266

ii.

Press the "Exit" button to finish beam axis adjustment.


iii.

Disconnect the GTS from the DLC3.



f.

After adjusting the radar beam axis, return the vehicle to its original condition.

i.

If any heavy items were removed from the vehicle, return them (luggage, heavy objects, etc.).


ii.

Install the cool air intake duct seal.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION