Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _034909 PRE-CRASH SAFETY _0163370 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1002  Lost Communication with Gateway Module  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects ahead to the driving support ECU assembly. The driving support ECU assembly sends this information to the ECM and performs pre-crash safety system operation.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor When the engine switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for 1.652 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


U1002 Lost Communication with Gateway Module When the engine switch is on (IG), a communication error between the millimeter wave radar sensor assembly and driving support ECU assembly is detected for 1.652 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


U1104 Lost Communication with Driving Support ECU When the engine switch is on (IG), a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for 1.192 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

A303847E37
0.073,1.688 1.01,2.083 0.938,0.396 10 false from IG1 NO. 3 Relay 1.438,1.823 2.031,2.167 0.594,0.344 10 false ECU-IG1 NO. 3 2.167,1.563 2.313,1.76 0.146,0.198 10 false 5 2.375,1.656 2.833,1.854 0.458,0.198 10 false IGB 3.083,2.115 3.698,2.313 0.615,0.198 10 false CA1P 3.083,2.771 3.698,2.969 0.615,0.198 10 false CA1N 2.385,3.344 3,3.542 0.615,0.198 10 false SGND 2.156,3.198 2.313,3.396 0.156,0.198 10 false 1 1.99,3.823 2.302,4.021 0.313,0.198 10 false A79 1.979,3.99 4.885,4.188 2.906,0.198 10 false Millimeter Wave Radar Sensor Assembly 3.594,1.927 3.75,2.125 0.156,0.198 10 false 3 3.594,2.573 3.75,2.771 0.156,0.198 10 false 2 2.813,0.625 4.5,0.823 1.688,0.198 10 false from IG1 NO. 3 Relay 4.563,0.781 5.135,1.125 0.573,0.344 10 false ECU-IG1 NO. 3 5.229,0.521 5.542,0.719 0.313,0.198 10 false 30 5.5,0.635 5.656,0.833 0.156,0.198 10 false B 5.198,1.927 5.51,2.125 0.313,0.198 10 false 40 5.219,2.615 5.531,2.813 0.313,0.198 10 false 18 5.24,3.24 5.552,3.438 0.313,0.198 10 false 25 5.49,2.115 6.104,2.313 0.615,0.198 10 false CA1P 5.49,2.75 6.104,2.948 0.615,0.198 10 false CA1N 5.5,3.344 5.958,3.542 0.458,0.198 10 false GND 5.188,3.896 5.5,4.094 0.313,0.198 10 false I191 5.198,4.063 7.115,4.573 1.917,0.51 10 false Driving Support ECU Assembly 0.885,4.375 2.688,4.563 1.802,0.188 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.


Result:
Result Proceed to
CAN communication is normal A
CAN communication is malfunctioning B



A

2.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)

B

2.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
E244596C25
1.552,0.417 1.885,0.635 0.333,0.219 2.469,2.469 1.906,2.469 1.906,2.469 1.771,1.927 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 2.51,2.396 2.708,2.604 0.198,0.208 10 false B 1.594,0.438 1.927,0.604 0.333,0.167 10 false I191
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the I191 driving support ECU assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I191-30 (B) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the I191 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)
a.
C319199C12
1.5,0.24 1.927,0.5 0.427,0.26 2.031,1.146 2.396,0.667 2.396,0.667 2.615,0.667 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.604,0.292 2.063,0.49 0.458,0.198 10 false A79 2.677,0.573 3.135,0.771 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A79 millimeter wave radar sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A79-5 (IGB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the A79 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.
C319199C13
1.5,0.24 1.927,0.5 0.427,0.26 1.354,1.146 0.938,0.656 0.938,0.656 0.75,0.656 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.604,0.292 2.063,0.49 0.458,0.198 10 false A79 0.333,0.583 0.792,0.781 0.458,0.198 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A79 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A79-1 (SGND) - Body ground Always Below 1 Ω



c.

Reconnect the A79 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS (PRE-CRASH 2)
6.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC U0235, U1002 and U1104 are not output A
DTC U0235, U1002 or U1104 is output B




A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY