Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _034909 PRE-CRASH SAFETY _0163370 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety System Switch Circuit  


DESCRIPTION

Each time the pre-crash system cancel switch assembly is pressed, the multi-information display sensitivity setting display changes to switch the sensitivity of the pre-crash safety system between 3 levels. Also, when the switch is pressed and held, the pre-crash safety system cancels.

WIRING DIAGRAM

E297408E20
5.198,2 5.594,2.156 0.396,0.156 10 false I191 5.198,2.146 7.094,2.344 1.896,0.198 10 false Driving Support ECU Assembly 5.521,1.042 6.042,1.188 0.521,0.146 10 false PBSW 5.323,0.927 5.49,1.094 0.167,0.167 10 false 5 3.583,0.927 3.896,1.104 0.313,0.177 10 false ECU 3.969,0.927 4.135,1.094 0.167,0.167 10 false 8 2.677,0.927 2.99,1.104 0.313,0.177 10 false GND 2.49,0.927 2.656,1.094 0.167,0.167 10 false 5 2.469,1.427 2.938,1.594 0.469,0.167 10 false I189 2.49,1.573 4.146,1.917 1.656,0.344 10 false Pre-Crash System Cancel Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS (PCS OFF SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PCS OFF Switch Pre-crash safety system switch status ON or OFF ON: Pre-crash safety system function disabled due to switch operation
OFF: Pre-crash safety system function enabled due to switch operation
-
Body Electrical > Pre-Crash 2 > Data List
Tester Display
PCS OFF Switch
50003 220 87
OK:

When the pre-crash safety system switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY
2.INSPECT PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY
a.

Remove the pre-crash system cancel switch assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM CANCEL SWITCH>REMOVAL


b.

Inspect the pre-crash system cancel switch assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM CANCEL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)

NG

REPLACE PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH SYSTEM CANCEL SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the I189 pre-crash system cancel switch assembly connector.


b.

Disconnect the I191 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I189-8 (ECU) - I191-5 (PBSW) Always Below 1 Ω
I189-8 (ECU) - Body ground Always 10 kΩ or higher
I189-5 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR