Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163371 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 8 functions: SET, -(COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, CANCEL and MODE. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while it is being operated and turns off when it is released. The driving support ECU assembly then reads the voltage value that has been changed by the switch operation to control MODE, SET, -, RES, +, or CANCEL function. The dynamic radar cruise control system has 2 cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode.

·

Vehicle-to-vehicle distance control mode is selected by default when the dynamic radar cruise control system is turned on using the cruise control main switch.

·

The operation of constant speed control mode is the same as that for a conventional cruise control system.


WIRING DIAGRAM

A303848E33
0.427,0.719 1.344,0.917 0.917,0.198 10 false CANCEL 1.073,0.729 1.688,0.927 0.615,0.198 10 false -/SET 1.552,0.729 2.167,0.927 0.615,0.198 10 false +/RES 2.063,0.729 2.677,0.927 0.615,0.198 10 false ON/OFF 2.448,0.438 2.906,0.635 0.458,0.198 10 false CCS 2.51,1.51 2.969,1.708 0.458,0.198 10 false R/N 2.083,1.74 2.698,1.938 0.615,0.198 10 false MODE 2.458,2.24 2.917,2.438 0.458,0.198 10 false ECC 0.708,2.927 2.594,3.438 1.885,0.51 10 false Cruise Control Main Switch 2.844,0.438 3,0.635 0.156,0.198 10 false 3 2.844,1.51 3,1.708 0.156,0.198 10 false 2 2.833,2.24 2.99,2.438 0.156,0.198 10 false 1 2.979,2.677 3.885,3.5 0.906,0.823 10 false Cruise Control Switch Wire 4.125,0.531 4.438,0.729 0.313,0.198 10 false z2 4.156,0.313 4.313,0.51 0.156,0.198 10 false 3 4.125,1.594 4.438,1.792 0.313,0.198 10 false z2 4.156,1.375 4.313,1.573 0.156,0.198 10 false 1 4.125,2.333 4.438,2.531 0.313,0.198 10 false z2 4.156,2.125 4.313,2.323 0.156,0.198 10 false 4 4.417,0.438 4.875,0.635 0.458,0.198 10 false CCS 4.76,0.438 5.219,0.635 0.458,0.198 10 false CCS 4.427,1.5 4.885,1.698 0.458,0.198 10 false R/N 4.813,1.5 5.271,1.698 0.458,0.198 10 false R/N 4.427,2.25 4.885,2.448 0.458,0.198 10 false ECC 4.781,2.25 5.24,2.448 0.458,0.198 10 false ECC 5.188,0.531 5.646,0.729 0.458,0.198 10 false I28 5.198,1.604 5.656,1.802 0.458,0.198 10 false I28 5.198,2.344 5.656,2.542 0.458,0.198 10 false I28 5.25,0.313 5.406,0.51 0.156,0.198 10 false 1 5.25,2.125 5.406,2.323 0.156,0.198 10 false 2 5.25,1.396 5.406,1.594 0.156,0.198 10 false 8 4.094,2.76 5.604,3.188 1.51,0.427 10 false Spiral Cable with Sensor Sub-assembly 6.042,0.438 6.354,0.635 0.313,0.198 10 false 40 6.042,1.5 6.354,1.698 0.313,0.198 10 false 38 6.271,0.531 6.729,0.729 0.458,0.198 10 false CCS 6.271,1.604 6.885,1.802 0.615,0.198 10 false CCHG 6.417,2.052 6.729,2.25 0.313,0.198 10 false A25 6.406,2.198 6.885,2.438 0.479,0.24 10 false ECM 0.708,2.781 0.865,2.979 0.156,0.198 10 false A

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PRECAUTION

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch signal (Main CPU) ON or OFF ON: Cruise control main switch on
OFF: Cruise control main switch off
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
MODE Change Switch MODE switch signal ON or OFF ON: MODE switch on
OFF: MODE switch off
-
Powertrain > Radar Cruise > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
MODE Change Switch
50003 239 15,22,21,20,49
OK:

When the cruise control main switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL


b.

Inspect the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT CRUISE CONTROL SWITCH WIRE

NG

3.INSPECT CRUISE CONTROL SWITCH WIRE
a.
A306566C37
1.083,2.75 1.417,3 0.333,0.25 1.083,0.417 1.417,0.667 0.333,0.25 0.708,1.875 1.125,1.625 true 0.667,1 1.125,1.25 true 1.375,1.615 1.833,1.865 true 1.5,3.854 1.958,4.104 true 1.063,3.844 0.583,4.167 true 1.292,3.875 1.292,4.292 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.115,2.74 0.427,2.896 0.313,0.156 10 false *b 1.177,0.469 1.458,0.646 0.281,0.177 10 false z2 1.208,2.792 1.49,2.969 0.281,0.177 10 false A 1.188,4.313 1.667,4.542 0.479,0.229 10 false R/N 0.385,1.802 0.781,2.031 0.396,0.229 10 false CCS 1.875,1.802 2.74,2.156 0.865,0.354 10 false ECC 0.281,4.094 0.635,4.281 0.354,0.188 10 false ECC 2.01,4.052 2.469,4.26 0.458,0.208 10 false CCS 0.417,0.906 0.76,1.125 0.344,0.219 10 false R/N
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Disconnect the cruise control switch wire.


b.

Disconnect the cruise control main switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-1 (R/N) - A-2 (R/N) Always Below 1 Ω
z2-3 (CCS) - A-3 (CCS) Always Below 1 Ω
z2-4 (ECC) - A-1 (ECC) Always Below 1 Ω
z2-1 (R/N) or A-2 (R/N) - Body ground Always 10 kΩ or higher
z2-3 (CCS) or A-3 (CCS) - Body ground Always 10 kΩ or higher
z2-4 (ECC) or A-1 (ECC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM)
a.

Disconnect the I28 spiral cable with sensor sub-assembly connector.


b.

Disconnect the A25 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I28-1 (CCS) - A25-40 (CCS) Always Below 1 Ω
I28-8 (R/N) - A25-38 (CCHG) Always Below 1 Ω
I28-2 (ECC) - Body ground Always Below 1 Ω
I28-1 (CCS) or A25-40 (CCS) - Body ground Always 10 kΩ or higher
I28-8 (R/N) or A25-38 (CCHG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR