Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163371 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Main Indicator Light Circuit  


DESCRIPTION

When the cruise control system is turned on using the cruise control main switch (ON-OFF button), the cruise control indicator light (vehicle-to-vehicle distance control mode) illuminates. The driving support ECU assembly uses these and other indicators to indicate the control condition (presence or absence of a vehicle in front, vehicle-to-vehicle distance, and set vehicle speed) and fail-safe state through the CAN communication system.

WIRING DIAGRAM

E230248E48
0.844,2.271 2.594,2.625 1.75,0.354 10 false : CAN Communication Line 1.01,1.906 2.885,2.083 1.875,0.177 10 false Combination Meter Assembly 1.01,1.729 1.385,1.948 0.375,0.219 10 false I18 5.26,1.75 5.656,1.948 0.396,0.198 10 false A25 4.917,0.698 5.354,0.875 0.438,0.177 10 false CANH 4.927,1.198 5.365,1.417 0.438,0.219 10 false CANL 2.104,0.677 2.542,0.906 0.438,0.229 10 false CANH 2.104,1.188 2.542,1.417 0.438,0.229 10 false CANL 2.615,0.49 2.938,0.76 0.323,0.271 10 false 16 4.667,0.5 4.875,0.708 0.208,0.208 10 false 13 4.667,1.021 4.875,1.219 0.208,0.198 10 false 26 2.615,1.01 2.906,1.229 0.292,0.219 10 false 15 5.26,1.938 5.844,2.219 0.583,0.281 10 false ECM

CAUTION / NOTICE / HINT

HINT:

If the vehicle in front in the same lane significantly decreases vehicle speed or another vehicle moves in front of this vehicle, adequate deceleration cannot be applied by the cruise control system and the vehicle-to-vehicle distance will become shorter. At this time, the system sounds the buzzer to warn the driver. The indicators for the dynamic radar cruise control system use CAN for communication. Therefore, if there are any indicator malfunctions, check for DTCs in the CAN communication system before troubleshooting this circuit.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All -
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

Result:
Result Proceed to
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. A
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. B



A

2.READ VALUE USING GTS (CCS INDICATOR M-CPU)

B

2.READ VALUE USING GTS (CCS INDICATOR M-CPU)
a.

Enter the following menus: Powertrain / Radar Cruise / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Indicator M-CPU Cruise indicator signal (Main CPU) ON or OFF ON: Cruise control indicator on
OFF: Cruise control indicator off
-
Powertrain > Radar Cruise > Data List
Tester Display
CCS Indicator M-CPU
50003 239 11

Result:
Result Proceed to
The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF switch). A
The cruise control indicator does not illuminate but the Data List item CCS Indicator M-CPU changes according to the operation of the cruise control main switch (ON-OFF switch). B
The cruise control indicator does not illuminate and the Data List item CCS Indicator M-CPU does not change according to the operation of the cruise control main switch (ON-OFF switch). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C