Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0163371 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Wiper Signal Circuit  


DESCRIPTION

When the driving support ECU assembly detects that the wipers are operating at high speed, control of vehicle speed by the dynamic radar cruise control system is canceled.

WIRING DIAGRAM

E234003E25
0.323,2.76 0.604,2.948 0.281,0.188 10 false I32 0.323,2.938 2.604,3.167 2.281,0.229 10 false Windshield Wiper Switch Assembly 5.156,2.719 5.5,2.948 0.344,0.229 10 false I191 5.417,1.5 5.813,1.667 0.396,0.167 10 false WIP2 5.167,1.396 5.375,1.563 0.208,0.167 10 false 32 5.146,2.885 7.125,3.083 1.979,0.198 10 false Driving Support ECU Assembly 1.969,1.385 2.177,1.552 0.208,0.167 10 false 1 1.708,1.5 1.917,1.667 0.208,0.167 10 false +2 3.615,1.656 4.333,1.823 0.719,0.167 10 false WIPER-S

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (WIP2 VOLTAGE)
a.
E244596C28
1.552,0.417 1.885,0.635 0.333,0.219 2.604,2.552 2.115,2.552 2.115,2.552 1.958,1.917 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 2.646,2.49 3.135,2.74 0.49,0.25 10 false WIP2 1.594,0.438 1.927,0.604 0.333,0.167 10 false I191
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the I191 driving support ECU assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I191-32 (WIP2) - Body ground Engine switch on (IG), windshield wiper switch assembly HI position 11 to 14 V



d.

Turn the engine switch off.


e.

Reconnect the I191 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - WINDSHIELD WIPER SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - WINDSHIELD WIPER SWITCH ASSEMBLY)
a.

Disconnect the I191 driving support ECU assembly connector.


b.

Disconnect the I32 windshield wiper switch assembly connector.


c.

Disconnect the I72 windshield wiper relay assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I191-32 (WIP2) - I32-1 (+2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
I191-32 (WIP2) or I32-1 (+2) - Body ground Always 10 kΩ or higher



e.

Reconnect the I72 windshield wiper relay assembly connector.


f.

Reconnect the I32 windshield wiper switch assembly connector.


g.

Reconnect the I191 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - WINDSHIELD WIPER SWITCH ASSEMBLY)