Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014581 CRUISE CONTROL _0073970 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise SET Indicator Light Circuit  


DESCRIPTION

·

The ECM turns on the SET indicator light by sending indicator output demand signals to the combination meter assembly using CAN communication.

·

The cruise control SET indicator light illuminates when the cruise control system is controlling vehicle speed.

·

The cruise control indicator light circuit uses CAN communication. If the cruise control indicator light is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.


WIRING DIAGRAM

PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
Multi-information Display (Segment Type) A
Multi-information Display (TFT Type) B



A

2.PERFORM ACTIVE TEST USING GTS (INDICAT. SET)

B

4.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
2.PERFORM ACTIVE TEST USING GTS (INDICAT. SET)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. SET Cruise control SET indicator light ON or OFF Multi-information display (Segment type)
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. SET
50004 122 91

Result:
Result Proceed to
The cruise control SET indicator illuminates or turns off according to the operation of the Active Test. A
The cruise control SET indicator does not illuminate or turn off according to the operation of the Active Test. B



A

3.READ VALUE USING GTS (SET/COAST SWITCH)

B

3.READ VALUE USING GTS (SET/COAST SWITCH)
a.

Enter the following menus: Powertrain / Cruise Control / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
Powertrain > Cruise Control > Data List
Tester Display
SET/COAST Switch
50003 237 22

Result:
Result Proceed to
The cruise control SET indicator illuminates and turns off according to the operation of the cruise control main switch (-/SET switch). A
The cruise control SET indicator does not illuminate but the Data List item SET/COAST Switch changes according to the operation of the cruise control main switch (-/SET switch). B
The cruise control SET indicator does not illuminate and the Data List item SET/COAST Switch does not change according to the operation of the cruise control main switch (-/SET switch). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C

4.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All Multi-information Display (TFT Type)
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

Result:
Result Proceed to
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. A
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. B



A

5.READ VALUE USING GTS (SET/COAST SWITCH)

B

5.READ VALUE USING GTS (SET/COAST SWITCH)
a.

Enter the following menus: Powertrain / Cruise Control / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SET/COAST Switch -/SET switch signal ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
Powertrain > Cruise Control > Data List
Tester Display
SET/COAST Switch
50003 237 22

Result:
Result Proceed to
The cruise control SET indicator illuminates and turns off according to the operation of the cruise control main switch (-/SET switch). A
The cruise control SET indicator does not illuminate but the Data List item SET/COAST Switch changes according to the operation of the cruise control main switch (-/SET switch). B
The cruise control SET indicator does not illuminate and the Data List item SET/COAST Switch does not change according to the operation of the cruise control main switch (-/SET switch). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C