Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


BLIND SPOT MONITOR BEAM AXIS INSPECTION


a.

Procedure to enter Test Mode

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the blind spot monitor main switch (warning canceling switch assembly) on.


iv.

Turn the GTS on.


v.

Switch the blind spot monitor sensor to Test Mode using the GTS. Enter the following menus: Body / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis inspection or BSM Slave beam axis inspection.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Inspection
50005 313 4202
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Inspection
50005 314 4203

vi.

Finish Test Mode.




BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

E224418E10
0.208,0.135 0.615,0.323 0.406,0.188 12 false LH: 4.042,0.135 4.417,0.323 0.375,0.188 12 false RH: 0.156,1.51 0.438,1.708 0.281,0.198 10 false 2 m 0.99,4.042 1.917,4.24 0.927,0.198 10 false 6 m (19.69 ft) 2.271,4 2.552,4.198 0.281,0.198 10 false 3 m 4.573,4.031 4.865,4.229 0.292,0.198 10 false 3 m 6.76,1.521 7.042,1.719 0.281,0.198 10 false 2 m 6.74,3.5 7.042,3.698 0.302,0.198 10 false 8 m 0.188,3.448 0.469,3.646 0.281,0.198 10 false 8 m 3.135,1.792 4,1.979 0.865,0.188 10 false Rear Bumper 1.438,0.385 2.656,0.573 1.219,0.188 10 false Left side of vehicle 4.552,0.385 5.865,0.573 1.313,0.188 10 false Right side of vehicle 1.292,4.385 2.375,4.583 1.083,0.198 10 false : Inspection Area 5.333,4.052 6.26,4.25 0.927,0.198 10 false 6 m (19.69 ft) 4.479,4.198 5.031,4.396 0.552,0.198 10 false (9.85 ft) 2.552,4.042 3.104,4.24 0.552,0.198 10 false (9.85 ft) 0.031,3.813 0.625,3.99 0.594,0.177 10 false (26.25 ft) 0.021,1.635 0.563,1.844 0.542,0.208 10 false (6.57 ft) 6.563,3.823 7.156,4 0.594,0.177 10 false (26.25 ft) 6.656,1.708 7.156,1.917 0.5,0.208 10 false (6.57 ft)

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place any objects other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 9 m (29.53 ft.) x L 10 m (32.81 ft.) x H 4 m (13.13 ft.)) shown in the illustration.

·

Check that DTC C1ABB and DTC C1ABC are not output.




b.

Place the reflector.

i.

Hang the string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle. (Mark (A) and (B))


ii.
E238824E05
1.427,1.281 1.198,1.563 false 3.021,1.281 3.177,1.646 false 0.635,1.281 1.094,0.469 false 1.094,0.469 1.292,0.469 false 1.354,0.406 2.719,0.625 1.365,0.219 10 false Vehicle center line 1.104,1.552 1.26,1.708 0.156,0.156 10 false A 3.188,1.646 3.344,1.802 0.156,0.156 10 false B

Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).


iii.
E238823E25
0.354,1.281 0.542,1.677 false 1.438,1.271 1.271,1.688 false 3.01,1.281 3.073,1.667 false 0.448,0.219 1.563,0.417 1.115,0.198 10 false 567 mm (1.86 ft.) 1.198,1.698 1.344,1.896 0.146,0.198 10 false A 0.552,1.688 0.698,1.885 0.146,0.198 10 false C 3.052,1.698 3.198,1.896 0.146,0.198 10 false B

Mark the position on the center line 567 mm (1.86 ft.) behind the rear bumper. (Mark (C))


iv.
E238825E07
1.708,3.781 2.156,3.302 false 0.24,3.458 1.406,3.667 1.167,0.208 10 false 300 mm (11.8 in.) 2.24,3.198 2.615,3.563 0.375,0.365 10 false C 0.281,0.135 1.177,0.292 0.896,0.156 10 false Vehicle front 0.229,3.938 1.396,4.146 1.167,0.208 10 false 300 mm (11.8 in.)

Prepare 2 pieces of string of 600 mm (1.97 ft.) in length and secure the end of each string at a point 300 mm (11.8 in.) from mark (C) as shown in the illustration.


v.
E271872E02
2.094,2.521 2.542,2.281 false 0.833,2.302 1.271,2.531 false 1.156,1.927 1.375,1.927 1.375,1.927 1.688,2.292 false 1.198,3.135 1.417,3.135 1.417,3.135 1.625,2.729 false 0.115,0.125 1.125,0.375 1.01,0.25 12 false Vehicle rear: 0.74,1.833 1.25,2.063 0.51,0.229 10 false String 0.677,2.208 0.927,2.406 0.25,0.198 10 false D 0.781,3.042 1.229,3.281 0.448,0.24 10 false String 2.615,2.167 2.844,2.354 0.229,0.188 10 false C

Pull the end of each string and mark the position where each string meets on the left side. (Mark (D))


vi.
E271873E02
1.688,0.51 2.281,0.219 false 0.792,4.198 1.052,3.938 false 1.323,4.25 1.448,3.938 false 0.323,0.135 1.188,0.302 0.865,0.167 10 false Vehicle front 2.365,0.135 3.281,0.521 0.917,0.385 10 false Vehicle center line 0.708,4.229 1,4.427 0.292,0.198 10 false D 1.167,4.302 1.656,4.51 0.49,0.208 10 false Line P

Draw a line (P) so that it passes through mark (D) and is perpendicular to the vehicle center line.


vii.
E238823E26
0.292,1.688 0.365,1.281 false 1.292,1.688 1.438,1.281 false 3.188,1.688 3.021,1.281 false 1.01,0.708 1.385,0.354 1.385,0.354 1.719,0.354 false 1.229,1.729 1.51,1.917 0.281,0.188 10 false A 3.167,1.729 3.365,1.969 0.198,0.24 10 false B 0.25,1.719 0.479,1.906 0.229,0.188 10 false E 1.792,0.26 2.969,0.469 1.177,0.208 10 false 555 mm (1.82 ft.)

Mark the position on the center line 555 mm (1.82 ft.) behind the rear bumper. (Mark (E))


viii.
E238825E06
1.719,3.771 2.167,3.219 false 2.167,3.219 2.354,3.219 false 0.135,3.375 1.302,3.583 1.167,0.208 10 false 300 mm (11.8 in.) 2.417,3.135 2.625,3.365 0.208,0.229 10 false E 0.26,0.063 1.156,0.219 0.896,0.156 10 false Vehicle front 0.135,3.833 1.302,4.042 1.167,0.208 10 false 300 mm (11.8 in.)

Prepare 2 pieces of string of 600 mm (1.97 ft.) in length and secure the end of each string at a point 300 mm (11.8 in.) from mark (E) as shown in the illustration.


ix.
E271874E02
0.958,2.302 1.583,2.552 false 2.406,2.552 2.76,2.385 false 2.01,2.313 2.208,1.833 2.208,1.833 2.417,1.833 false 2.052,2.76 2.198,3.156 2.198,3.156 2.406,3.156 false 0.094,0.083 1.104,0.333 1.01,0.25 12 false Vehicle rear: 0.771,2.208 1.01,2.448 0.24,0.24 10 false E 2.833,2.271 3.073,2.51 0.24,0.24 10 false F 2.49,1.74 3.031,1.979 0.542,0.24 10 false String 2.479,3.073 2.938,3.281 0.458,0.208 10 false String

Pull the end of each string and mark the position where each string meets on the right side. (Mark (F))


x.
E271875E02
1.698,0.521 2.26,0.24 false 2.313,3.927 2.583,4.26 false 1.896,3.938 2.083,4.26 false 0.313,0.135 1.219,0.313 0.906,0.177 10 false Vehicle front 2.354,0.156 3.281,0.656 0.927,0.5 10 false Vehicle center line 2.573,4.302 2.99,4.51 0.417,0.208 10 false F 1.948,4.313 2.469,4.5 0.521,0.188 10 false Line Q

Draw a line (Q) so that it passes through mark (F) and is perpendicular to the vehicle center line.


xi.

Set the reflector at the position Z shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E233794E43
0.688,3.229 1.094,2.917 false 6.24,3.073 5.906,2.885 false 2.688,2.208 2.917,1.781 false 2.917,1.781 3.052,1.781 false 4.385,2.208 4.135,1.792 false 4.135,1.792 3.979,1.792 false 5.313,2.563 5.552,1.781 false 5.552,1.781 5.698,1.781 false 2.01,2.385 1.74,1.854 false 1.74,1.854 1.573,1.854 false 2.563,2.865 2.719,3.156 false 2.719,3.156 2.771,3.156 false 4.542,2.854 4.365,3.146 false 4.365,3.146 4.302,3.146 false 1.188,2.833 1.063,2.323 false 1.063,2.323 0.99,2.323 false 5.854,2.813 5.969,2.323 false 5.969,2.323 6.031,2.323 false 0.542,0.031 0.875,0.26 0.333,0.229 12 false LH: 3.448,0.01 3.781,0.24 0.333,0.229 12 false RH: 4.104,0.156 5.313,0.323 1.208,0.167 10 false Vehicle center line 2.833,2.313 3.365,2.5 0.531,0.188 10 false 567 mm 0.875,2.24 1.031,2.427 0.156,0.188 10 false Z 6.052,2.24 6.177,2.427 0.125,0.188 10 false Z 0.323,3.26 0.917,3.427 0.594,0.167 10 false Reflector 6.063,3.104 6.656,3.271 0.594,0.167 10 false Reflector 1.76,0.188 2.969,0.354 1.208,0.167 10 false Vehicle center line 3.094,1.667 3.969,1.833 0.875,0.167 10 false Rear bumper 3.729,2.313 4.26,2.5 0.531,0.188 10 false 555 mm 1.49,3.135 2.104,3.323 0.615,0.188 10 false 3114 mm 5.719,1.656 6.333,1.844 0.615,0.188 10 false 3182 mm 0.979,1.76 1.594,1.948 0.615,0.188 10 false 3165 mm 0.958,1.917 1.594,2.104 0.635,0.188 10 false (10.38 ft.) 5.719,1.813 6.354,2 0.635,0.188 10 false (10.44 ft.) 5.063,3.24 5.698,3.427 0.635,0.188 10 false (10.28 ft.) 1.49,3.302 2.125,3.49 0.635,0.188 10 false (10.21 ft.) 2.792,2.479 3.427,2.667 0.635,0.188 10 false (1.86 ft.) 3.729,2.458 4.365,2.646 0.635,0.188 10 false (1.82 ft.) 2.792,3.052 3.281,3.219 0.49,0.167 10 false Line P 3.885,3.042 4.375,3.208 0.49,0.167 10 false Line Q 5.031,3.063 5.646,3.25 0.615,0.188 10 false 3133 mm

NOTICE:
·
E238830E16
0.469,1.469 0.74,1.698 0.271,0.229 10 false A

Set the reflector so that its center is 480 mm (1.57 ft.) above the ground.

·
E238829E05
1.979,0.677 2.469,1.302 false 1.865,1.281 3.094,1.625 1.229,0.344 10 false Center of triangular pyramid

The center of the triangular pyramid is the reference point for the setting position and angle.

·

Set the reflector as shown in the illustration so that the center of the triangular pyramid faces the blind spot monitor sensor.

·

Perform the operation as precisely as possible.





c.

Perform the blind spot monitor beam axis display.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the blind spot monitor main switch (warning canceling switch assembly) on.


iv.

Turn the GTS on.


v.

Enter the following menus: Body / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Display
50005 313 4238
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Display
50005 314 4239

vi.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor RH (Master) Blind Spot Monitor Sensor LH (Slave)
Angle -3.6 to +3.6 ° -3.6 to +3.6 °
Distance 2.0 to 3.0 m
(6.57 to 9.85 ft.)
2.0 to 3.0 m
(6.57 to 9.85 ft.)


HINT:

If the results are outside the allowable range, try again as the reflector setting position may be incorrect or a metal object may exist near the detection area.



vii.

Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body / Blind spot monitor Master or Blind spot monitor Slave / Utility /BSM Master beam axis adjustment or BSM Slave beam axis adjustment.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Adjustment
50005 313 4231
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Beam Axis Adjustment
50005 314 4232
HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates for any deviation from the normal value.





BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



a.

Remove the rear bumper assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER>REMOVAL


b.

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.

E233717E01
5.912,3.961 5.912,3.413 false 6.081,3.343 6.913,3.527 0.832,0.184 10 Floor surface 5.912,3.413 6.059,3.413 false 1.953,3.588 1.953,2.446 false 1.189,3.588 2.903,3.753 1.714,0.166 10 Blind Spot Monitor Sensor 3.125,3.441 4.816,3.645 1.691,0.205 10 Outward facing surface 2.298,2.115 2.983,3.504 false 0.161,0.064 1.797,0.248 1.635,0.184 10 Rear view of vehicle (RH): 5.056,1.213 5.582,0.619 false 5.582,0.619 5.729,0.619 false 5.764,0.556 6.208,0.793 0.444,0.236 10 Jig 4.611,3.251 4.874,3.251 false 4.909,3.19 5.483,3.426 0.574,0.236 10 Weight 2.983,3.504 3.095,3.504 false

E233716E10
1.677,0.885 3.042,1.417 1.365,0.531 10 false Hold this side against the blind spot monitor sensor RH. 3.26,1.76 3.542,1.969 0.281,0.208 10 false Top 5.333,3.146 5.906,3.333 0.573,0.188 10 false 100 mm 2.76,4.083 2.948,4.271 0.188,0.188 10 false A 3.979,4.083 4.167,4.271 0.188,0.188 10 false B 1.354,2.823 2.844,3.167 1.49,0.344 10 false Position where string is to be secured 1.042,6.177 2.51,6.604 1.469,0.427 10 false : Allowable range 0.219,0.188 0.833,0.427 0.615,0.24 12 false Jig: 1.552,4.979 1.74,5.167 0.188,0.188 10 false + 5.167,4.979 5.354,5.167 0.188,0.188 10 false - 5.354,3.292 6,3.479 0.646,0.188 10 false (3.94 in.) 4.156,0.896 5.531,1.5 1.375,0.604 10 false Hold this side against the blind spot monitor sensor LH.

Standard:
A B
Blind spot monitor sensor RH 8 mm (0.315 in.) -8 mm (-0.315 in.)
Blind spot monitor sensor LH 8 mm (0.315 in.) -8 mm (-0.315 in.)



c.
E224437E18
1.229,3.625 1.469,4.031 false 2.26,0.583 2.479,0.583 2.479,0.583 2.917,1.167 false 0.781,3.573 0.729,3.854 false 0.552,3.833 0.271,3.906 false 0.271,3.906 0.271,4.281 false 1.427,2 1.594,1.667 false 1.594,1.667 1.667,1.667 false 1.469,4.031 1.563,4.031 false 0.094,0 1.448,0.208 1.354,0.208 12 false Vehicle rear (LH): 1.094,0.49 2.26,0.802 1.167,0.313 10 false Vehicle center line 1.594,3.979 2.219,4.146 0.625,0.167 10 false Stud bolt 1.448,0.896 2.24,1.063 0.792,0.167 10 false Vehicle front 0.688,3.823 0.813,3.99 0.125,0.167 10 false y 1.938,3.708 2.698,3.875 0.76,0.167 10 false Vehicle rear 0.052,4.292 2.427,4.458 2.375,0.167 10 false Line parallel to the vehicle center line 1.656,2.385 2.344,2.573 0.688,0.188 10 false 104 mm 1.74,1.594 2.74,2.01 1,0.417 10 false Stud bolt center line 1.688,2.594 2.375,2.781 0.688,0.188 10 false (4.09 in.)

Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
y 29 to 42 mm (1.14 to 1.65 in.)