Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.04
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074248 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Parking Brake Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the parking brake switch assembly.

WIRING DIAGRAM

B242655E17
5.479,2.052 7.115,2.552 1.635,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 4.281,1.063 5.885,1.396 1.604,0.333 10 false Instrument Panel Junction Block Assembly 0.958,1.063 3.177,1.74 2.219,0.677 10 false Parking Brake Switch Assembly 4.813,0.75 5.208,1.125 0.396,0.375 10 false 3D 4.823,0.542 5.26,0.854 0.438,0.313 10 false 20 5.75,0.635 6.052,1.083 0.302,0.448 10 false 12 5.99,0.76 6.375,1.115 0.385,0.354 10 false PKB 5.479,1.875 5.74,2.25 0.26,0.375 10 false MB 0.958,0.906 1.354,1.365 0.396,0.458 10 false A42 1.75,0.635 1.854,0.813 0.104,0.177 10 false 1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch signal ON or OFF ON: Parking brake switch on
OFF: Parking brake switch off
-
Body Electrical > Main Body > Data List
Tester Display
Parking Brake SW
50003 123 12
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the parking brake switch assembly.

for Automatic Transaxle LHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for Automatic Transaxle LHD)>REMOVAL

for Automatic Transaxle RHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for Automatic Transaxle RHD)>REMOVAL


b.

Inspect the parking brake switch assembly.

for Automatic Transaxle LHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for Automatic Transaxle LHD)>INSPECTION

for Automatic Transaxle RHD: Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH(for Automatic Transaxle RHD)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-1 - 3D-20 Always Below 1 Ω
A42-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.
E182506C13
1.479,0.771 1.969,1.063 0.49,0.292 1.479,2.938 1.969,3.229 0.49,0.292 1.302,3.49 1.302,3.75 false 0.188,0.177 1.073,0.74 0.885,0.563 10 false *a 1.646,0.844 2.479,1.542 0.833,0.698 10 false 3D 1.625,3.01 2.177,3.354 0.552,0.344 10 false MB 1.135,3.76 1.917,4.292 0.781,0.531 10 false PKB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-20 - MB-12 (PKB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY