Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a ground short in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB3 Short to GND in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time.


·

Outer mirror LH

·

Outer rear view mirror assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E314323E09
1.604,1.26 1.76,1.458 0.156,0.198 10 false 1 1.604,1.74 1.74,1.896 0.135,0.156 10 false 2 1.302,1.365 1.458,1.563 0.156,0.198 10 false + 1.313,1.823 1.469,2.021 0.156,0.198 10 false - 0.271,2.188 0.885,2.385 0.615,0.198 10 false IND2 0.271,2.365 2.563,2.563 2.292,0.198 10 false Outer Mirror LH 0.26,2.646 2.427,3.031 2.167,0.385 10 false (Outer Rear View Mirror Indicator LH) 2.885,1.354 3.344,1.552 0.458,0.198 10 false z6 2.917,1.615 3.156,1.823 0.24,0.208 10 false 12 2.885,1.833 3.344,2.031 0.458,0.198 10 false z6 5.76,1.208 6.219,1.406 0.458,0.198 10 false 4 4.563,1.146 4.823,1.354 0.26,0.208 10 false 10 2.958,1.156 3.115,1.354 0.156,0.198 10 false 7 4.521,1.354 4.979,1.552 0.458,0.198 10 false K12 4.094,1.833 4.552,2.031 0.458,0.198 10 false GND 4.615,1.635 5.073,1.833 0.458,0.198 10 false 7 5.969,1.354 6.427,1.552 0.458,0.198 10 false OMIL 5.906,3.542 7.094,3.938 1.188,0.396 10 false Blind Spot Monitor Sensor LH 4,1.365 4.458,1.563 0.458,0.198 10 false BDSL 0.177,3.448 2.521,3.698 2.344,0.25 10 false Outer Rear View Mirror Assembly LH 3.198,3.417 4.75,3.771 1.552,0.354 10 false Outer Mirror Control ECU Assembly LH 5.906,3.385 6.365,3.583 0.458,0.198 10 false T21 4.552,1.833 5.01,2.031 0.458,0.198 10 false K12 3.271,1.354 3.729,1.552 0.458,0.198 10 false BDIL 3.292,1.823 3.75,2.021 0.458,0.198 10 false HTR-

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Disconnect the T21 blind spot monitor sensor LH connector.


b.

Disconnect the K12 outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-10 (BDSL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Disconnect the z6 outer mirror control ECU assembly LH connector.


b.

Disconnect the IND2 outer mirror LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z6-7 (BDIL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.

Disconnect the K12 outer mirror control ECU assembly LH connector.


b.
E233744C67
2.219,0.208 2.646,0.469 0.427,0.26 2.552,1.26 2.76,1.708 false 2.302,0.26 2.583,0.417 0.281,0.156 10 false K12 2.594,1.719 3.073,1.917 0.479,0.198 10 false BDSL 0.094,0.031 0.292,0.229 0.198,0.198 10 false *a
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-10 (BDSL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER MIRROR LH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

5.INSPECT OUTER MIRROR LH

b.

Inspect the outer rear view mirror indicator LH on the outer mirror LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

6.RECHECK DTC

NG

REPLACE OUTER MIRROR LH

6.RECHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR LH WAS DEFECTIVE)

NG