This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and the navigation receiver assembly itself will not function.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
w/ VSC: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PRECAUTION
w/o VSC: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>PRECAUTION
Disconnect the I67 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-21 (SW1) - I67-23 (SWG) | No switch pushed | 95 to 105 kΩ |
| Up switch pushed | Below 2.5 Ω | |
| Down switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| I67-22 (SW2) - I67-23 (SWG) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 313 to 345 Ω | |
| Off hook switch pushed | 950 to 1050 Ω | |
| Voice switch pushed | 2955 to 3265 Ω | |
| I67-24 (SW3) - I67-23 (SWG) | No switch pushed | 95 to 105 kΩ |
| Enter switch pushed | Below 2.5 Ω | |
| Back switch pushed | 313 to 345 Ω | |
| Right switch pushed | 950 to 1050 Ω | |
| Left switch pushed | 2955 to 3265 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Volume+ |
| *c | Volume- | *d | Back |
| *e | MODE/HOLD | *f | Up |
| *g | Down | *h | Left |
| *i | Right | *j | Enter |
| *k | Off hook | *l | On hook |
| *m | Voice | - | - |
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Volume+ |
| *c | Volume- | *d | Back |
| *e | MODE/HOLD | *f | Up |
| *g | Down | *h | Left |
| *i | Right | *j | Enter |
| *k | Off hook | *l | On hook |
| *m | Voice | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 11 (AU1) - 8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Up switch pushed | Below 2.5 Ω | |
| Down switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| 10 (AU2) - 8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 313 to 345 Ω | |
| Off hook switch pushed | 950 to 1050 Ω | |
| Voice switch pushed | 2955 to 3265 Ω | |
| 9 (AU3) - 8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Enter switch pushed | Below 2.5 Ω | |
| Back switch pushed | 313 to 345 Ω | |
| Right switch pushed | 950 to 1050 Ω | |
| Left switch pushed | 2955 to 3265 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
| *b | Steering Pad Switch Assembly Side |
| *c | Vehicle Side |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-8 (EAU) - I28-3 (EAU) | Center | 3 Ω or less |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-11 (AU1) - I28-6 (AU1) | Center | 3 Ω or less |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-10 (AU2) - I28-5 (AU2) | Center | 3 Ω or less |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-9 (AU3) - I28-4 (AU3) | Center | 3 Ω or less |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-8 (EAU) - I28-3 (EAU) | Always | 3 Ω or less |
| z3-11 (AU1) - I28-6 (AU1) | Always | 3 Ω or less |
| z3-10 (AU2) - I28-5 (AU2) | Always | 3 Ω or less |
| z3-9 (AU3) - I28-4 (AU3) | Always | 3 Ω or less |
Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.
The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
| Proceed to |
|---|
| OK |
| NG |
OK
NG