Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › 2014.05–2016.05
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0164321 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E305031E06
2.24,0.313 3.375,0.583 1.135,0.271 10 false from TAIL Relay 4,0.479 4.583,0.75 0.583,0.271 10 false PANEL 0.396,3.042 2.823,3.385 2.427,0.344 10 false Steering Pad Switch Assembly 2.823,2.24 3.917,3 1.094,0.76 10 false Spiral Cable Sub-assembly 5.74,2.823 6.958,3.573 1.219,0.75 10 false Navigation Receiver Assembly 2.719,1.219 3.031,1.427 0.313,0.208 10 false z3 2.719,1.781 3.031,1.99 0.313,0.208 10 false z3 3.771,1.229 4.083,1.469 0.313,0.24 10 false I28 3.76,1.781 4.073,2.021 0.313,0.24 10 false I28 5.563,1.229 5.875,1.469 0.313,0.24 10 false I64 5.573,1.792 5.885,2.031 0.313,0.24 10 false I67 5.563,2.354 5.875,2.594 0.313,0.24 10 false I65 5.917,1.229 6.24,1.469 0.323,0.24 10 false ILL+ 5.885,1.792 6.448,2.052 0.563,0.26 10 false SWG 5.896,2.375 6.219,2.615 0.323,0.24 10 false ILL- 3.188,1.115 3.531,1.365 0.344,0.25 10 false IL+2 3.177,1.688 3.542,1.948 0.365,0.26 10 false EAU 2.75,1.031 2.969,1.24 0.219,0.208 10 false 5 5.625,2.156 5.844,2.365 0.219,0.208 10 false 5 2.75,1.594 2.969,1.802 0.219,0.208 10 false 8 3.781,1.042 4.01,1.271 0.229,0.229 10 false 13 5.573,1.031 5.802,1.26 0.229,0.229 10 false 10 5.583,1.594 5.813,1.823 0.229,0.229 10 false 23 3.813,1.604 4.031,1.813 0.219,0.208 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

w/ VSC: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PRECAUTION

w/o VSC: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation receiver assembly. B
No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the I28 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I28-13 (IL+2) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.

for LHD
E309447C01
3.115,1.229 3.406,1.01 false 3.74,0.896 4.073,0.656 false 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 2.844,1.25 3.521,1.521 0.677,0.271 10 false EAU 4.104,0.479 4.781,0.75 0.677,0.271 10 false IL+2
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


for RHD
E309448C01
3.135,1.25 3.417,1.021 false 3.75,0.896 4.042,0.635 false 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.854,1.271 3.646,1.458 0.792,0.188 10 false EAU 4.073,0.458 4.865,0.646 0.792,0.188 10 false IL+2
*a Component without harness connected
(Steering Pad Switch Assembly)
- -



c.

Check if the illumination for the steering pad switch assembly comes on.

OK:

Illumination for the steering pad switch assembly comes on.



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.
E268445C52
1.583,0.313 1.906,0.51 0.323,0.198 1.583,3.417 1.906,3.615 0.323,0.198 1.583,0.865 1.208,1.156 false 1.552,4.104 1.167,4.24 false 2.188,1.26 1.896,1.042 false 2.302,3.76 1.865,4.01 false 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.75,0.219 1.063,0.417 0.313,0.198 10 false *b 1.677,0.323 1.99,0.521 0.313,0.198 10 false z3 0.906,1.094 1.24,1.292 0.333,0.198 10 false IL+2 0.74,3.313 1.052,3.51 0.313,0.198 10 false *c 1.656,3.427 1.969,3.625 0.313,0.198 10 false I28 0.875,4.188 1.208,4.385 0.333,0.198 10 false IL+2 2.26,1.177 2.813,1.458 0.552,0.281 10 false EAU 2.375,3.646 2.948,3.927 0.573,0.281 10 false EAU
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z3-8 (EAU) - I28-3 (EAU) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Always 3 Ω or less
z3-8 (EAU) - I28-3 (EAU) Always 3 Ω or less


NOTICE:
·

Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.




Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY, BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the I64 navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I64-10 (ILL+) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the I65 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I65-5 (ILL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR