The skid control ECU receives stop light switch signals and uses them to determine whether or not the brakes are applied.
The skid control ECU has a detection circuit that it uses to detect a short in the stop light input line, or the ground line of the stop light circuit with the stop light switch on (brake pedal depressed).
If the skid control ECU detects a short in this circuit, it will store this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1426 | Stop Light Switch OFF Stuck Malfunction | Either of the following is detected:
1.
With the stop light switch off, the stop light switch is judged to be on based on the master cylinder pressure value for 3 seconds or more. 2.
With the stop light switch off, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi) for 3 seconds or more. |
·
STOP fuse ·
Stop light switch assembly ·
Stop light control relay (STOP relay) (w/ Dynamic radar cruise control system) ·
Stop light switch circuit ·
Ground circuit ·
Skid control ECU (Brake actuator assembly) |
Refer to DTC C1249.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249
Check the brake pedal height and stop light switch assembly installation.
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT
The brake pedal height and stop light switch assembly installation are normal.
If the on/off status of the stop light switch assembly and the pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and switch before inspecting the input signals and other related parts.
| Result | Proceed to |
|---|---|
| OK | A |
| NG(for LHD) | B |
| NG(for RHD) | C |
A
B
C
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Stop Light SW |
Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.
The intelligent tester displays on or off according to brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1426 is not output. | A |
| DTC C1426 is output. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-38 (GND1) - Body ground | Always | Below 1 Ω |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Check that the STOP (7.5 A) fuse is normal.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A33 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-2 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Stop Light Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Switch pin free | Below 1 Ω |
| 1 - 2 | Switch pin pushed in | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (w/ Dynamic Radar Cruise Control System) | A |
| OK (w/o Dynamic Radar Cruise Control System) | B |
| NG | C |
A
B
C
| *1 | No. 2 Engine Room Relay Block |
| *2 | Stop Light Control Relay (STOP Relay) |
Remove the stop light control relay (STOP relay).
Reconnect the A33 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Stop light control relay (STOP relay) terminal 4 - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| Stop light control relay (STOP relay) terminal 4 - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Stop Light Control Relay (STOP Relay) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 4 | Voltage is not applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 4 | Voltage is applied between terminals 1 and 2 | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Install the stop light control relay (STOP relay).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| A49-30 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| A49-22 (STP2) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| A49-22 (STP2) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A49 skid control ECU connector.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1426 is not output. | A |
| DTC C1426 is output. | B |
If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Reconnect the A33 stop light switch assembly connector.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| A49-30 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A49 skid control ECU connector.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1426 is not output. | A |
| DTC C1426 is output. | B |
If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B