Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL(for RHD) › from 2015.04
RM19V0EQ _54 Brake _014592 BRAKE SYSTEM (OTHER) _0074043 BRAKE PEDAL(for RHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for RHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Check the brake pedal height.

i.

Turn back the carpet.


ii.

Turn back the dash panel insulator assembly from the slit provided on the dash panel insulator assembly.


iii.
C238433C01
2.146,1.854 2.708,1.854 false 1.708,3.854 1.104,3.854 false 2.708,1.76 3.052,2.021 0.344,0.26 10 *1 0.948,3.781 1.333,4.083 0.385,0.302 10 *2 2.552,3.813 2.938,4.083 0.385,0.271 10 *a
*1 Stop Light Switch Assembly
*2 Asphalt Sheet
*a Brake Pedal Height


Measure the shortest distance between the brake pedal pad surface and asphalt sheet.

Pedal height from asphalt sheet:

143.2 to 153.2 mm (5.64 to 6.03 in.)


If pedal height is incorrect, inspect and adjust the push rod length according to the procedure below.



b.

Adjust the push rod length.

i.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Remove the brake booster assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL


iii.
C105620C01
1.927,1.208 1.927,1.563 false 2.24,1.208 2.24,1.563 false 1.708,0.25 2.167,0.573 0.458,0.323 10 *a 1.844,1.573 2.135,1.771 0.292,0.198 10 *1 2.167,1.573 2.677,1.865 0.51,0.292 10 *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis
*a Push Rod Length


Loosen the lock nut and adjust the push rod length shown in the illustration by turning the brake master cylinder push rod clevis to achieve the correct length.

Push rod length:

148.6 to 149.6 mm (5.86 to 5.88 in.)



iv.

Tighten the lock nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


v.

Install the brake booster assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>INSTALLATION

·

If the pedal height is incorrect even when the push rod length is adjusted, check the brake pedal support assembly and floor panel.

·

If necessary, replace the brake pedal support assembly.



vi.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION



c.

After adjusting the pedal height, check the brake pedal free play.


Hide 2.INSPECT BRAKE PEDAL FREE PLAY

a.

Stop the engine and firmly depress the brake pedal several times until no vacuum is left in the booster.


b.
C132708C02
2.156,1.573 2.615,1.792 0.458,0.219 10 false *a
*a Brake Pedal Free Play


Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

Pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 3.INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:

Measure the distance at the same point used for the brake pedal height inspection.


a.

Release the parking brake.


b.

With the engine running, depress the brake pedal and measure the pedal reserve distance.

Pedal Reserve Distance from the Asphalt Sheet at 500 N (51 kgf, 112 lbf):

More than 98 mm (3.86 in.)


If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE