Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.04
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.

Pressing the vehicle stability control switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF indicator light will come on (w/o Multi-information Display) or the TRC OFF message will be displayed on the multi-information display (w/ Multi-information Display) and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C239016E21
5.469,4.01 7.083,4.354 1.615,0.344 10 false Skid Control ECU (Brake Actuator Assembly) 5.469,3.865 5.875,4.156 0.406,0.292 10 false A49 0.26,4.01 1.542,4.354 1.281,0.344 10 false Combination Meter Assembly 0.26,3.865 0.573,4.021 0.313,0.156 10 false I18 5.969,0.906 6.417,1.063 0.448,0.156 10 false CANL 5.969,1.708 6.417,1.865 0.448,0.156 10 false CANH 5.688,0.802 5.906,0.958 0.219,0.156 10 false 14 5.688,1.625 5.938,1.854 0.25,0.229 10 false 26 0.896,0.906 1.344,1.063 0.448,0.156 10 false CANL 0.896,1.708 1.344,1.865 0.448,0.156 10 false CANH 1.396,0.792 2.344,1.042 0.948,0.25 10 false 15*1, 16*2 1.396,1.615 2.333,1.802 0.938,0.188 10 false 16*1, 17*2 5.969,2.865 6.417,3.021 0.448,0.156 10 false CSW 5.729,2.771 6.063,3.052 0.333,0.281 10 false 9 3.656,3.396 5.156,3.771 1.5,0.375 10 false Vehicle Stability Control Switch 3.656,3.24 4.083,3.594 0.427,0.354 10 false I173 4.844,2.76 5.063,2.917 0.219,0.156 10 false 9 3.792,2.76 4.01,2.917 0.219,0.156 10 false 6 4.625,2.979 4.844,3.135 0.219,0.156 10 false + 3.979,2.979 4.198,3.135 0.219,0.156 10 false E 1.823,4.063 3.906,4.25 2.083,0.188 10 false *1: w/o Multi-information Display 1.823,4.406 4.198,4.625 2.375,0.219 10 false *2: w/ Multi-information Display

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
Unknown: Unspecified
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

d.

Check the indicator light and mode condition on the intelligent tester changes according to vehicle stability control switch operation.

Standard:
Switch Operation Mode Condition Display TRC OFF Indicator Light*1
Multi-information Display (TRC OFF Message)*2
VSC OFF Indicator Light
Not pressed Normal Does not come on*1
Not displayed*2
Does not come on
Pressing the vehicle stability control switch TRC OFF Comes on*1
Displayed*2
Does not come on
Pressing and holding the vehicle stability control switch VSC OFF Comes on*1
Displayed*2
Comes on


*1: w/o Multi-information Display

*2: w/ Multi-information Display



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light Multi-information display (TRC OFF message)*1
TRC OFF indicator light*2
Display (message) ON/OFF*1
Indicator light ON/OFF*2
Observe combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly

*1: w/ Multi-information Display

*2: w/o Multi-information Display


Chassis > ABS/VSC/TRC > Active Test
Tester Display
TRC(TRAC) OFF Indicator Light
50004 105 78
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC OFF Indicator Light
50004 105 79

b.

Check the TRC OFF indicator light (w/o Multi-information Display) or multi-information display (TRC OFF message) (w/ Multi-information Display) and VSC OFF indicator light in the combination meter assembly turn on or off in accordance with intelligent tester operation.

OK:

The TRC OFF indicator light (w/o Multi-information Display) or multi-information display (TRC OFF message) (w/ Multi-information Display) and VSC OFF indicator light turn on or off in accordance with intelligent tester operation.



Result:
Proceed to
OK
NG



OK

5.INSPECT VEHICLE STABILITY CONTROL SWITCH

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VEHICLE STABILITY CONTROL SWITCH
a.
C311100C03
1.375,2.729 1.521,2.104 false 2.302,2.698 2.115,2.104 false 0.49,0.573 0.802,0.771 0.313,0.198 10 false *a 1.313,2.75 1.625,2.948 0.313,0.198 10 false + 2.313,2.74 2.625,2.938 0.313,0.198 10 false E
*a Component without harness connected
(Vehicle Stability Control Switch)


Turn the ignition switch off.


b.

Disconnect the I173 vehicle stability control switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (+) - 6 (E) Switch pushed Below 1 Ω
9 (+) - 6 (E) Switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VEHICLE STABILITY CONTROL SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VEHICLE STABILITY CONTROL SWITCH)
a.

Disconnect the A49 skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-9 (CSW) - I173-9 (+) Always Below 1 Ω
A49-9 (CSW) - Body ground Always 10 kΩ or higher
I173-6 (E) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform an Active Test of the combination meter assembly using the intelligent tester (w/o Multi-information Display).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
VSC TRC Indicator
50004 122 102
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

c.

Perform an Active Test of the combination meter assembly using the intelligent tester (w/ Multi-information Display).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

d.

Check the combination meter assembly.

OK:

The TRC OFF indicator light (w/o Multi-information Display) or multi-information display (w/ Multi-information Display) and VSC OFF indicator light turn on or off in accordance with intelligent tester operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG