ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM
V Bus
ECM
Brake actuator assembly
Main body ECU (multiplex network body ECU)
Air conditioning amplifier assembly
Power steering ECU assembly
Network gateway ECU*1
Smart key ECU assembly (certification ECU)*2
Airbag sensor assembly
Steering sensor*7
Combination meter assembly
Navigation receiver assembly*3
Radio and display receiver assembly*4
Clearance warning ECU assembly*6
Sub Bus 1*5
Main body ECU (multiplex network body ECU)
Outer mirror control ECU assembly (for driver side)
Outer mirror control ECU assembly (for front passenger side)
Position control ECU and switch assembly (for driver side)
Sub Bus 2*1
Network gateway ECU
Rear television camera assembly
Blind spot monitor sensor RH*8
Driving support ECU assembly*8
Lane departure warning camera*8
Sub Bus 13*8
Driving support ECU assembly
Millimeter wave radar sensor assembly
*1: w/ Parking Assist Monitor System or Pre-crash Safety System
*2: w/ Smart Entry and Start System
*3: for Navigation Receiver Type
*4: for Radio and Display Type
*5: w/ Seat Position Memory System
*6: w/ Toyota Parking Assist-sensor System
*7: w/ VSC
*8: w/ Pre-crash Safety System
CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.
The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section that follows.
| ECU/Sensor Name | GTS Display | Applicability |
|---|---|---|
| ECM | ECM (Engine) | Installed on all vehicles |
| Clearance warning ECU assembly | Clearance Warning (Clearance Sonar2) | Vehicles with Toyota Parking Assist-sensor System |
| Combination meter assembly | Combination Meter | Installed on all vehicles |
| Main body ECU (multiplex network body ECU) | Main Body | Installed on all vehicles |
| Power steering ECU assembly | Power Steering (EPS) | Installed on all vehicles |
| Brake actuator assembly | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles |
| Steering sensor | Spiral cable (Steering Angle Sensor) | Vehicles with VSC |
| Airbag sensor assembly | Airbag | Installed on all vehicles |
| Smart key ECU assembly (certification ECU) | Certification (Smart) | Vehicles with Smart Entry and Start System |
| Air conditioning amplifier assembly | Air Conditioning Amplifier | Installed on all vehicles |
| Navigation receiver assembly | Display and Navigation (AVN1) | Vehicles with Navigation Receiver Type |
| Radio and display receiver assembly | Display and Navigation (AVN1) | Vehicles with Radio and Display Type |
| Network gateway ECU | CAN Gateway1 | Vehicles with Parking Assist Monitor System or Pre-crash Safety System |
| Blind spot monitor sensor RH | Blind Spot Monitor Master | Vehicles with Pre-crash Safety System |
| Outer mirror control ECU assembly (for front passenger side) | Front Door LH/L-Mirror (FL-Door2/L-Miror) | Vehicles with Seat Position Memory System |
| Outer mirror control ECU assembly (for driver side) | Front Door RH/R-Mirror (FR-Door2/R-Miror) | Vehicles with Seat Position Memory System |
| Position control ECU and switch assembly (for driver side) | D-Seat | Vehicles with Seat Position Memory System |
| Rear television camera assembly | Parking Assist Monitor System3 | Vehicles with Parking Assist Monitor System or Pre-crash Safety System |
| Lane departure warning camera | Front Camera Module | Vehicles with Pre-crash Safety System |
| Driving support ECU assembly | Driving Support (Cruise Control-ACC) | Vehicles with Pre-crash Safety System |
| Millimeter wave radar sensor assembly | - | Vehicles with Pre-crash Safety System |
CAN BUS CHECK
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.
Using the GTS, select the CAN Bus Check screen.
It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)
In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| V Bus | White | Communication has been normal since the start of the CAN Bus Check. |
| Yellow | Communication stop occurred at least once since the start of the CAN Bus Check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN Bus Check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN Bus Check.*1 | |
| Sub Bus
(gateway function equipped ECU that does not have history of connected ECUs)*2 |
White | Communication has been normal since the start of the CAN Bus Check. |
| Yellow | Communication stop occurred at least once since the start of the CAN Bus Check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN Bus Check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN Bus Check.*1 | |
| Sub Bus
(gateway function equipped ECU that has history of connected ECUs)*3 |
White | Communication has been normal since the start of the CAN Bus Check. |
| Yellow | Communication stop occurred at least once since the start of the CAN Bus Check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Communication stop has continued since the start of the CAN Bus Check. ·
Communication was established at least once since the start of the CAN Bus Check, but communication is currently not occurring. |
|
| Not displayed | Either of the following:
·
If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed. ·
If no ECUs are connected to the sub bus, ''There is no system found on the Communication Bus'' will be displayed. |
Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the DLC3 branch and the V bus main bus lines for a malfunction.
Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.
If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.
If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN Bus Check again.
HOW TO INTERPRET CAN BUS CHECK SCREEN
When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN Bus Check and by using the following methods.
The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.
When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN Bus Check rather than from communication DTCs.
Wait for approximately 2 minutes after turning the ignition switch to ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.
If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.
Example: Open in both CAN branch lines of ECU B on the V bus
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color changes to red or yellow | *f | CAN Bus Check Screen |
When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.
| *a | Background color periodically changes to yellow or red |
| *b | Not displayed or background color is yellow or red |
| *c | Not displayed |
If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor which is not displayed) is suspected.
Example: Open in a CAN branch line for ECU D on the V bus
| Bus Type | Background Color | Connection Status |
|---|---|---|
| V Bus | White | Communication has been normal since the start of the CAN Bus Check. |
| Yellow | Communication stop occurred at least once since the start of the CAN Bus Check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN Bus Check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN Bus Check.*1 | |
| Sub Bus
(gateway function equipped ECU that does not have history of connected ECUs)*2 |
White | Communication has been normal since the start of the CAN Bus Check. |
| Yellow | Communication stop occurred at least once since the start of the CAN Bus Check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN Bus Check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN Bus Check.*1 | |
| Sub Bus
(gateway function equipped ECU that has history of connected ECUs)*3 |
White | Communication has been normal since the start of the CAN Bus Check. |
| Yellow | Communication stop occurred at least once since the start of the CAN Bus Check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Communication stop has continued since the start of the CAN Bus Check. ·
Communication was established at least once since the start of the CAN Bus Check, but communication is currently not occurring. |
|
| Not displayed | Either of the following:
·
If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed. ·
If no ECUs are connected to the sub bus, ''There is no system found on the Communication Bus'' will be displayed. |
Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.
The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.
| *a | Not displayed or background color changes to red |
If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.
Example: Open in both CAN branch lines of ECU C on the V bus
In the CAN Bus Check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.
If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.
The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.
| *a | Background color changes to red |
If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
Example: Open in both CAN branch lines of ECU G on the sub bus
A communication error in a sub bus does not affect the V bus or other buses.
When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)
If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, ECU A and B are not displayed or their background color changes to red.)
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color is red | *f | CAN Bus Check Screen |
If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.
If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, ECU I and J are not displayed or their background color changes to red.)
| *a | V Bus | *b | Sub Bus |
| *c | Terminating Resistor | *d | Location of Malfunction |
| *e | Not displayed or background color is red | *f | CAN Bus Check Screen |
| *g | Gateway Function Equipped ECU | - | - |
| *a | When any of the following malfunctions occur on the V bus |
| *b | When any of the following malfunctions occur on a sub bus |
| *c | Not displayed |
When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.
| Short between CAN lines (CANH and CANL) |
| Short between a CAN line (CANH or CANL) and +B |
| Short between a CAN line (CANH or CANL) and ground |
| Open in a CAN main bus line |
When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).
When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.
A communication error in a sub bus does not affect the V bus or other buses.
The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.
HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)
If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.
Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.
If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.
| *a | Items to be Checked | - | - |
This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)
As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.
If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.
| *a | Items to be Checked | - | - |
This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.
When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with B or C) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.
To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.
| *a | Items to be Checked | *b | ECM |
| *c | Gateway Function Equipped ECU | *d | Location of Malfunction |
| *e | V Bus | *f | Sub Bus |
This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.
As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.
When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and ground
Short between a CAN line (CANH or CANL) and +B
Open in a CAN branch line (CANH or CANL) of an ECU or sensor
Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor
DTC TABLE BY ECU
In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If the system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.
ECM / GTS Display "Engine and ECT"
This ECU uses the CAN communication system for DTC communication.
*1: Refer to U760E Automatic Transaxle System.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>U0100
*2: Refer to SFI System.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>U0101
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100*1 | Lost Communication with ECM / PCM "A" | The transmission control ECU does not receive data from the engine control ECU for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | MIL illuminates. | DTC remains stored only while malfunction is occurring. |
| U0101*2 | Lost Communication with TCM | The engine control ECU does not receive data from the transmission control ECU for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | MIL illuminates. | DTC remains stored only while malfunction is occurring. |
Power Steering ECU Assembly / GTS Display "EMPS"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The power steering ECU assembly does not receive data from the ECM for 5 minutes or more. | All conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. ·
Vehicle speed is 20 km/h (12 mph) or more. |
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. | - | DTC remains stored only while malfunction is occurring. |
| U0129 | Lost Communication with Brake System Control Module | The power steering ECU assembly does not receive data from the brake actuator assembly for 2.34 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait at least 6 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
Brake Actuator Assembly (w/o VSC) / GTS Display "ABS/VSC/TRC"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus OFF | Bus off is judged for 0.1 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the brake actuator assembly (+BS terminal voltage) is between 9.6 and 16.5 V. |
Turn the ignition switch to ON and check that the initial light check illumination turns off, and then wait at least 3 seconds. | ·
ABS warning light illuminates. ·
Brake warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
Brake Actuator Assembly (w/ VSC) / GTS Display "ABS/VSC/TRC"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus OFF | Bus off is judged for 0.1 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the brake actuator assembly (+BS terminal voltage) is between 9.6 and 16.5 V. |
Turn the ignition switch to ON and check that the initial light check illumination turns off, and then wait at least 3 seconds. | ·
ABS warning light illuminates. ·
Slip indicator light illuminates. ·
Brake warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM / PCM | The brake actuator assembly does not receive data from the ECM for 2.5 seconds or more. | All conditions are met:
·
Vehicle speed is 6 km/h (4 mph) or more. ·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the brake actuator assembly (+BS terminal voltage) is between 9.6 and 16.5 V. |
Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 6 seconds or more. Check that the warning light remains off after turning off following the initial light check. | Slip indicator light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The brake actuator assembly does not receive data from the airbag sensor assembly for 1.1 seconds or more. | All conditions are met:
·
Vehicle speed is 6 km/h (4 mph) or more. ·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the brake actuator assembly (+BS terminal voltage) is between 9.6 and 16.5 V. |
Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 3 seconds or more. Check that the warning light remains off after turning off following the initial light check. | Slip indicator light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The brake actuator assembly does not receive data from the steering sensor for 1.1 seconds or more. | All conditions are met:
·
Vehicle speed is 6 km/h (4 mph) or more. ·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the brake actuator assembly (+BS terminal voltage) is between 9.6 and 16.5 V. |
Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 3 seconds or more. Check that the warning light remains off after turning off following the initial light check. | Slip indicator light illuminates. | DTC is stored until it is cleared using the GTS. |
Steering Sensor / GTS Display "-"
The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.
Airbag Sensor Assembly / GTS Display "SRS Airbag"
The airbag sensor assembly is connected to the CAN communication system, but the airbag sensor assembly does not store or output CAN communication DTCs.
Smart Key ECU Assembly (Certification ECU) / GTS Display "Entry&Start"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM | The smart key ECU assembly (certification ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Main Body ECU | The smart key ECU assembly (certification ECU) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"
This ECU uses the CAN communication system for DTC communication.
*: w/ Seat Position Memory System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The main body ECU (multiplex network body ECU) does not receive data from the TCM for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0120 | Lost Communication with Starter / Generator Control Module | The main body ECU (multiplex network body ECU) does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Restraints Control Module | The main body ECU (multiplex network body ECU) does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The main body ECU (multiplex network body ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Lost Communication with HVAC Control Module | The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The main body ECU (multiplex network body ECU) does not receive data from the lane departure warning camera for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0327 | Software Incompatibility with Vehicle Security Control Module | The main body ECU (multiplex network body ECU) does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module (Main body ECU) | The main body ECU (multiplex network body ECU) does not receive data from ECUs with a sub bus 1 connection record for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0199 | Lost Communication with ''Door Control Module A'' | The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0200 | Lost Communication with ''Door Control Module B'' | The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0208 | Lost Communication with ''Seat Control Module A'' | The main body ECU (multiplex network body ECU) does not receive data from the position control ECU and switch assembly (for driver side) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Smart Key ECU Assembly (Certification ECU) / GTS Display "Power Source Control"
This ECU uses the CAN communication system for DTC communication.
*1: w/o Multi-information Display
*2: w/ Multi-information Display
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM | The smart key ECU assembly (certification ECU) does not receive data from the ECM for 3.1 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Main Body ECU | The smart key ECU assembly (certification ECU) does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 3.1 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | ·
The smart entry and start system warning light (orange) blinks for 15 seconds when the ignition switch is turned from ON to off.*1 ·
Displays messages on the multi-information display.*2 |
DTC is stored until it is cleared using the GTS. |
Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM | The air conditioning amplifier assembly does not receive data from the ECM for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Electric Power Steering ECU | The air conditioning amplifier assembly does not receive data from the power steering ECU assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Main Body ECU | The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Combination Meter | The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
Combination Meter Assembly / GTS Display "Combination Meter"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The combination meter assembly does not receive data from the ECM for 2 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the combination meter assembly is between 9.5 and 11.5 V. |
Turn the ignition switch to ON and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Skid Control ECU | The combination meter assembly does not receive data from the brake actuator assembly for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the combination meter assembly is between 9.5 and 11.5 V. |
Turn the ignition switch to ON and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The combination meter assembly does not receive data from the power steering ECU assembly for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the combination meter assembly is between 9.5 and 11.5 V. |
Turn the ignition switch to ON and wait at least 3 seconds. | EPS warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Main Body ECU | The combination meter assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the combination meter assembly is between 9.5 and 11.5 V. |
Turn the ignition switch to ON and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Airbag ECU | The combination meter assembly does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the combination meter assembly is between 9.5 and 11.5 V. |
Turn the ignition switch to ON and wait at least 10 seconds. | SRS warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | The combination meter assembly does not receive data from the navigation receiver assembly for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the combination meter assembly is between 9.5 and 11.5 V. |
Turn the ignition switch to ON and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The combination meter assembly does not receive data from the lane departure warning camera for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the combination meter assembly is between 9.5 and 11.5 V. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1104 | Lost Communication with Driving Support ECU | The combination meter assembly does not receive data from the driving support ECU assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the combination meter assembly is between 9.5 and 11.5 V. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Clearance Warning ECU Assembly / GTS Display "Clearance Sonar"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The clearance warning ECU assembly does not receive data from the ECM for 5.75 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 7.75 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The clearance warning ECU assembly does not receive data from the TCM for 8.07 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 10.07 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The clearance warning ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 5.9 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 7.9 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) | The clearance warning ECU assembly does not receive data from the combination meter assembly for 6.5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 8.5 seconds. | - | DTC is stored until it is cleared using the GTS. |
Navigation Receiver Assembly / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The navigation receiver assembly does not send/receive data for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ACC for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ACC and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine ECU Communication | The navigation receiver assembly does not receive data from the ECM for 4 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | VSC (ECB) ECU Communication | The navigation receiver assembly does not receive data from the brake actuator assembly for 1 second or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The navigation receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The navigation receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Air Conditioner ECU Communication | The navigation receiver assembly does not receive data from the air conditioning amplifier assembly for 15 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 16 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1110 | Clearance Sonar ECU Communication | The navigation receiver assembly does not receive data from the clearance warning ECU assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
Radio and Display Receiver Assembly / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly does not send/receive data for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ACC for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ACC and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine ECU Communication | The radio and display receiver assembly does not receive data from the ECM for 4 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | VSC (ECB) ECU Communication | The radio and display receiver assembly does not receive data from the brake actuator assembly for 1 second or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Air Conditioner ECU Communication | The radio and display receiver assembly does not receive data from the air conditioning amplifier assembly for 15 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 16 seconds. | - | DTC is stored until it is cleared using the GTS. |
Network Gateway ECU / GTS Display "Gateway"
This ECU uses the CAN communication system for DTC communication.
"Gateway" stores DTCs when a communication error is detected in the Sub bus 2.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0104 | Lost Communication with Cruise Control Module | The network gateway ECU does not receive data from the driving support ECU assembly. | The ignition switch is ON for 22 seconds or more. | Turn the ignition switch to ON and wait at least 22 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0233 | Lost Communication with Blind Spot Monitor Master Module | The network gateway ECU does not receive data from the blind spot monitor sensor RH. | The ignition switch is ON for 22 seconds or more. | Turn the ignition switch to ON and wait at least 22 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The network gateway ECU does not receive data from the lane departure warning camera. | The ignition switch is ON for 22 seconds or more. | Turn the ignition switch to ON and wait at least 22 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0265 | Lost Communication with Parking Assist Monitor Module | The network gateway ECU does not receive data from the rear television camera assembly. | The ignition switch is ON for 22 seconds or more. | Turn the ignition switch to ON and wait at least 22 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module (Network Gateway ECU) | The network gateway ECU detects communication errors between itself and the driving support ECU assembly, lane departure warning camera, blind spot monitor sensor RH and rear television camera assembly. | The ignition switch is ON for 22 seconds or more. | Turn the ignition switch to ON and wait at least 22 seconds. | - | DTC is stored until it is cleared using the GTS. |
Blind Spot Monitor Sensor RH / GTS Display "Blind Spot Monitor Master"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Blind Spot Monitor System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The blind spot monitor sensor RH does not receive data from the TCM for 10.84 seconds or more. | All conditions are met:
·
Blind spot monitor main switch on. ·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. ·
Vehicle speed is 5 km/h (3 mph) or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.84 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The blind spot monitor sensor RH does not receive data from the steering sensor for 10.68 seconds or more. | All conditions are met:
·
Blind spot monitor main switch on. ·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.68 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The blind spot monitor sensor RH does not receive data from the brake actuator assembly for 2.334 seconds or more. | All conditions are met:
·
Blind spot monitor main switch on. ·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 4.334 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The blind spot monitor sensor RH does not receive data from the main body ECU (multiplex network body ECU) for 10.6 seconds or more. | All conditions are met:
·
Blind spot monitor main switch on. ·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0232* | Lost Communication with Blind Spot Monitor Slave Module | The blind spot monitor sensor RH does not receive data from the blind spot monitor sensor LH for 10.6 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the blind spot monitor sensor RH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1331* | Software Incompatibility with Body Control Module "B" | Destination information of the main body ECU and blind spot monitor sensor do not match. | All conditions are met:
·
Blind spot monitor main switch on. ·
The ignition switch is ON. |
Destination information of the main body ECU and blind spot monitor sensor do not match. | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
Position Control ECU and Switch Assembly (for Driver Side) / GTS Display "Driver Seat"
The position control ECU and switch assembly (for driver side) is connected to the CAN communication system, but the position control ECU and switch assembly (for driver side) does not store or output CAN communication DTCs.
Outer Mirror Control ECU Assembly (for Driver Side) / GTS Display "Mirror R"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0142 | Lost Communication with Body Control Module ''B'' | The outer mirror control ECU assembly (for driver side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the combination meter assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Outer Mirror Control ECU Assembly (for Front Passenger Side) / GTS Display "Mirror L"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0142 | Lost Communication with Body Control Module ''B'' | The outer mirror control ECU assembly (for front passenger side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
10 seconds have elapsed after connection of the battery. ·
The power source voltage of the combination meter assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Rear Television Camera Assembly / GTS Display "IPA/Parking Assist Monitor"
This ECU uses the CAN communication system for DTC communication.
*: The rear television camera assembly stores this DTC if an internal error related to the CAN communication system is detected.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The rear television camera assembly does not receive data from the ECM for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The rear television camera assembly does not receive data from the steering sensor for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The rear television camera assembly does not receive data from the brake actuator assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The rear television camera assembly does not receive data from the power steering ECU assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The rear television camera assembly does not receive data from the main body ECU (multiplex network body ECU) for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ACC for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the ignition switch to ACC and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | The rear television camera assembly does not receive data from the navigation receiver assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ACC for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the ignition switch to ACC and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure (Message Registry) | When the ignition switch is turned on, a CAN communication malfunction is detected. | The ignition switch is ON. | Turn the ignition switch to ON. | - | DTC remains stored only while malfunction is occurring. |
| U1110 | Lost Communication with Clearance Sonar Module | The rear television camera assembly does not receive data from the clearance warning ECU assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the rear television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
Lane Departure Warning Camera / GTS Display "Lane Departure Alert"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Lane Departure Alert System.
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>U1000
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The lane departure warning camera does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The lane departure warning camera does not receive data from the TCM for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The lane departure warning camera does not receive data from the airbag sensor assembly for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The lane departure warning camera does not receive data from the brake actuator assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the ignition switch to ON and wait at least 7 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module ''B'' | The lane departure warning camera does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the ignition switch to ON and wait at least 7 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module (Combination Meter) | The lane departure warning camera does not receive data from the combination meter assembly for 50 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the ignition switch to ON and wait at least 52 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure (Message Registry) | When the ignition switch is turned ON, a CAN communication malfunction is detected. | The ignition switch is ON. | Turn the ignition switch to ON. | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
Driving Support ECU Assembly / GTS Display "Pre-Crash 2"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Pre-crash Safety System.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>U0235
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0125 | Lost Communication with Yaw Rate Sensor Module | The driving support ECU assembly does not receive data from the airbag sensor assembly (yaw rate sensor) for 0.772 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 3.772 seconds. | PCS indicator light flashes. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The driving support ECU assembly does not receive data from the steering sensor for 3.76 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 4.76 seconds. | PCS indicator light flashes. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The driving support ECU assembly does not receive data from the brake actuator assembly for 5.24 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 7.24 seconds. | PCS indicator light flashes. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The driving support ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 14.2 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 15.2 seconds. | PCS indicator light flashes. | DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.652 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 1.652 seconds. | PCS indicator light flashes. | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module | The driving support ECU assembly does not receive data from ECU with a sub bus 13 connection record for 0.652 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 1.652 seconds. | PCS indicator light flashes. | DTC is stored until it is cleared using the GTS. |
| U1104* | Lost Communication with Driving Support ECU | The ECM, brake actuator assembly or millimeter wave radar sensor assembly does not receive data from the driving support ECU assembly for 1.504 seconds or more. | The ignition switch is ON for 2 seconds or more. | Turn the ignition switch to ON and wait at least 3.504 seconds. | PCS indicator light flashes. | DTC is stored until it is cleared using the GTS. |
ECM / GTS Display "Radar Cruise"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Dynamic Radar Cruise Control System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | ·
The driving support ECU assembly is unable to receive certain data from the ECM for 0.15 seconds or more. ·
The brake actuator assembly is unable to receive certain data from the ECM for 1 second or more. |
All conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. ·
Vehicle speed is 36 km/h (22 mph) or more. |
After turning the ignition switch to ON, turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0122 | Lost Communication with Vehicle Dynamics Control Module | When the vehicle speed is being controlled by the cruise control system in vehicle-to-vehicle distance control mode, the ECM does not receive data from the brake actuator assembly for 2.73 seconds or more. | All conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. ·
Vehicle speed is 36 km/h (22 mph) or more. |
After turning the ignition switch to ON, turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 2.73 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The ECM detects a communication error signal from the driving support ECU assembly (the driving support ECU assembly does not receive data from the yaw rate sensor) for 0.15 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. |
Allow the radar cruise control system (vehicle control mode) to operate for 0.15 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The ECM detects a communication error signal from the driving support ECU assembly (the driving support ECU assembly does not receive data from the steering sensor) for 0.15 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. |
Allow the radar cruise control system (vehicle control mode) to operate for 0.15 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The ECM detects a communication error signal from the driving support ECU assembly (the driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly) for 0.15 seconds or more. | All conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. ·
Vehicle speed is 36 km/h (22 mph) or more. |
After turning the ignition switch to ON, turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 0.15 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1102* | Lost Communication with Radar Sensor | The ECM detects a communication error signal (from the driving support ECU assembly to the millimeter wave radar sensor) for 0.15 seconds or more while the dynamic radar cruise control is in operation. | All conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. ·
Vehicle speed is 36 km/h (22 mph) or more. |
After turning the ignition switch to ON, turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 0.15 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1104 | Lost Communication with Driving Support ECU | The ECM is unable to receive certain data from the driving support ECU assembly for 1.23 seconds or more. | All conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. ·
Vehicle speed is 36 km/h (22 mph) or more. |
After turning the ignition switch to ON, turn the cruise control main switch on and drive the vehicle at 36 km/h (22 mph) or more for 1.23 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Millimeter Wave Radar Sensor Assembly / GTS Display "-"
The millimeter wave radar sensor assembly is connected to the CAN communication system, but the millimeter wave radar sensor assembly does not store or output CAN communication DTCs.
DTC COMBINATION TABLE (OPEN OR SHORT IN V BUS, PAST COMMUNICATION ERROR)
Regarding the past communication error of ECUs and sensors connected to the V bus (in this case, normal was displayed when performing the CAN Bus Check, but communication DTCs are output), the probable CAN bus line(s) that had a malfunction can be determined based on the following DTC combination table.
Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.
Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN Bus Check using the GTS because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).
If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 7 to 9) first.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
| - | Trouble Mode (CAN Bus Line Short Circuit or Short to GND) | ||
|---|---|---|---|
| V Bus | |||
| Output ECU | Output DTC | CANH - CANL
CANH - Ground short CANL - Ground short |
|
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | ○ | |
| U0131 | ○ | ||
| U0142 | ○ | ||
| U0155 | ○ | ||
·
Navigation Receiver Assembly*2*4 ·
Radio and Display Receiver Assembly*3*4 |
U0100 | ○ | |
| U0129 | ○ | ||
| U0140 | ○ | ||
| U0155 | ○ | ||
| U0164 | ○ | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | ○ | |
| U0101 | ○ | ||
| U0120 | ○ | ||
| U0151 | ○ | ||
| U0155 | ○ | ||
| U0164 | ○ | ||
| U0327 | ○ | ||
| ECM | - | - | |
| Network Gateway ECU*1 | - | - | |
| Power Steering ECU Assembly | U0100 | ○ | |
| U0129 | ○ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | ○ | |
| U0140 | ○ | ||
| U0142 | ○ | ||
| U0155 | ○ | ||
| Combination Meter Assembly | U0100 | ○ | |
| U0129 | ○ | ||
| U0131 | ○ | ||
| U0142 | ○ | ||
| U0151 | ○ | ||
| Steering Sensor | - | - | |
| Brake Actuator Assembly*4 | U0100 | ○ | |
| U0123 | ○ | ||
| U0126 | ○ | ||
| Sub Bus 2 | Network Gateway ECU*1 | U0265 | - |
| U1002 | - | ||
| Rear Television Camera Assembly | U0100 | ○ | |
| U0126 | ○ | ||
| U0129 | ○ | ||
| U0131 | ○ | ||
| U0140 | ○ | ||
| U0163 | ○ | ||
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
| - | Trouble Mode (CAN Bus Line Short Circuit or Short to GND) | ||
|---|---|---|---|
| V Bus | |||
| Output ECU | Output DTC | CANH - CANL
CANH - Ground short CANL - Ground short |
|
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | ○ | |
| U0131 | ○ | ||
| U0142 | ○ | ||
| U0155 | ○ | ||
·
Navigation Receiver Assembly*2*4 ·
Radio and Display Receiver Assembly*3*4 |
U0100 | ○ | |
| U0129 | ○ | ||
| U0140 | ○ | ||
| U0155 | ○ | ||
| U0164 | ○ | ||
| U1110 | ○ | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | ○ | |
| U0101 | ○ | ||
| U0120 | ○ | ||
| U0151 | ○ | ||
| U0155 | ○ | ||
| U0164 | ○ | ||
| U023A | ○ | ||
| U0327 | ○ | ||
| Network Gateway ECU*1 | - | - | |
| Clearance Warning ECU Assembly | U0100 | ○ | |
| U0101 | ○ | ||
| U0142 | ○ | ||
| U0155 | ○ | ||
| ECM | U0100 | ○ | |
| U0122 | ○ | ||
| U0123 | ○ | ||
| U0126 | ○ | ||
| U1104 | ○ | ||
| Power Steering ECU Assembly | U0100 | ○ | |
| U0129 | ○ | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | ○ | |
| U0140 | ○ | ||
| U0142 | ○ | ||
| U0155 | ○ | ||
| Combination Meter Assembly | U0100 | ○ | |
| U0129 | ○ | ||
| U0131 | ○ | ||
| U0142 | ○ | ||
| U0151 | ○ | ||
| U0163 | ○ | ||
| U023A | ○ | ||
| U1104 | ○ | ||
| Steering Sensor | - | - | |
| Brake Actuator Assembly*4 | U0100 | ○ | |
| U0123 | ○ | ||
| U0126 | ○ | ||
| Sub bus 2 | Network Gateway ECU*1 | U0104 | ○ |
| U0233 | - | ||
| U023A | - | ||
| U0265 | - | ||
| U1002 | - | ||
| Blind Spot Monitor Sensor RH | U0100 | ○ | |
| U0126 | ○ | ||
| U0129 | ○ | ||
| U0142 | ○ | ||
| Rear Television Camera Assembly | U0100 | ○ | |
| U0126 | ○ | ||
| U0129 | ○ | ||
| U0131 | ○ | ||
| U0140 | ○ | ||
| U0163 | ○ | ||
| U1110 | ○ | ||
| Lane Departure Warning Camera | U0100 | ○ | |
| U0101 | ○ | ||
| U0123 | ○ | ||
| U0129 | ○ | ||
| U0142 | ○ | ||
| U0155 | ○ | ||
| Driving Support ECU Assembly | U0125 | ○ | |
| U0126 | ○ | ||
| U0129 | ○ | ||
| U0142 | ○ | ||
| Sub bus 1 | Main Body ECU (Multiplex Network Body ECU)*1 | U0199 | - |
| U0200 | - | ||
| U0208 | - | ||
| U1002 | - | ||
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | |
| Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | |
| Position Control ECU and Switch Assembly (for Driver Side) | - | - | |
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
DTC COMBINATION TABLE (OPEN OR SHORT IN SUB BUS 1, PAST COMMUNICATION ERROR)
Regarding the past communication error of ECUs and sensors connected to the sub bus 1 (in this case, normal was displayed when performing the CAN Bus Check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the Main Body ECU (Multiplex Network Body ECU).
As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
DTCs output from ECUs other than the main body ECU (multiplex network body ECU)(gateway function equipped ECU) are shown only as a reference.
Regarding a communication stop that is currently occurring in the sub bus 1, the malfunctioning part can be confirmed easily by performing the CAN Bus Check using the GTS.
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
| - | Trouble Mode (CAN Bus Line Short Circuit or Short to GND) | ||
|---|---|---|---|
| Sub bus 1 | |||
| Output ECU | Output DTC | CANH - CANL
CANH - Ground short CANL - Ground short |
|
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | |
| U0131 | - | ||
| U0142 | - | ||
| U0155 | - | ||
·
Navigation Receiver Assembly*2*4 ·
Radio and Display Receiver Assembly*3*4 |
U0100 | - | |
| U0129 | - | ||
| U0140 | - | ||
| U0155 | - | ||
| U0164 | - | ||
| U1110 | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | |
| U0101 | - | ||
| U0120 | - | ||
| U0151 | - | ||
| U0155 | - | ||
| U0164 | - | ||
| U023A | - | ||
| U0327 | - | ||
| Network Gateway ECU*1 | - | - | |
| V Bus | Clearance Warning ECU Assembly | U0100 | - |
| U0101 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| ECM | U0100 | - | |
| U0122 | - | ||
| U0123 | - | ||
| U0126 | - | ||
| U1104 | - | ||
| Power Steering ECU Assembly | U0100 | - | |
| U0129 | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | |
| U0140 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| Combination Meter Assembly | U0100 | - | |
| U0129 | - | ||
| U0131 | - | ||
| U0142 | - | ||
| U0151 | - | ||
| U0163 | - | ||
| U023A | - | ||
| U1104 | - | ||
| Steering Sensor | - | - | |
| Brake Actuator Assembly*4 | U0100 | - | |
| U0123 | - | ||
| U0126 | - | ||
| Sub bus 2 | Network Gateway ECU*1 | U0104 | - |
| U0233 | - | ||
| U023A | - | ||
| U0265 | - | ||
| U1002 | - | ||
| Blind Spot Monitor Sensor RH | U0100 | - | |
| U0126 | - | ||
| U0129 | - | ||
| U0142 | - | ||
| Rear Television Camera Assembly | U0100 | - | |
| U0126 | - | ||
| U0129 | - | ||
| U0131 | - | ||
| U0140 | - | ||
| U0163 | - | ||
| U1110 | - | ||
| Lane Departure Warning Camera | U0100 | - | |
| U0101 | - | ||
| U0123 | - | ||
| U0129 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| Driving Support ECU Assembly | U0125 | - | |
| U0126 | - | ||
| U0129 | - | ||
| U0142 | - | ||
| Sub bus 1 | Main Body ECU (Multiplex Network Body ECU)*1 | U0199 | ○ |
| U0200 | ○ | ||
| U0208 | ○ | ||
| U1002 | ○ | ||
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | ○ | |
| Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | ○ | |
| Position Control ECU and Switch Assembly (for Driver Side) | - | - | |
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
DTC COMBINATION TABLE (OPEN OR SHORT IN SUB BUS 2, PAST COMMUNICATION ERROR)
Regarding the past communication error of ECUs and sensors connected to the sub bus 2 (in this case, normal was displayed when performing the CAN Bus Check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the Network Gateway ECU.
As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
DTCs output from ECUs other than the network gateway ECU (gateway function equipped ECU) are shown only as a reference.
Regarding a communication stop that is currently occurring in the sub bus 2, the malfunctioning part can be confirmed easily by performing the CAN Bus Check using the GTS.
If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.
○: Set
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
| - | Trouble Mode (Open in Both CAN Main Bus Lines) | Trouble Mode (CAN Bus Line Short to GND) | |||
|---|---|---|---|---|---|
| Sub Bus 2 | |||||
| Output ECU | Output DTC | CANH - CANL | CANH - Ground short | CANL - Ground short | |
| V Bus | Airbag Sensor Assembly | - | - | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | - | - | |
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
·
Navigation Receiver Assembly*2*4 ·
Radio and Display Receiver Assembly*3*4 |
U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0140 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| V Bus | Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | - | - |
| U0101 | - | - | - | ||
| U0120 | - | - | - | ||
| U0151 | - | - | - | ||
| U0155 | - | - | - | ||
| U0164 | - | - | - | ||
| U0327 | - | - | - | ||
| ECM | - | - | - | - | |
| Network Gateway ECU*1 | - | - | - | - | |
| Power Steering ECU Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| Smart Key ECU Assembly (Certification ECU) | U0100 | - | - | - | |
| U0140 | - | - | - | ||
| U0142 | - | - | - | ||
| U0155 | - | - | - | ||
| Combination Meter Assembly | U0100 | - | - | - | |
| U0129 | - | - | - | ||
| U0131 | - | - | - | ||
| U0142 | - | - | - | ||
| U0151 | - | - | - | ||
| Steering Sensor | - | - | - | - | |
| Brake Actuator Assembly*4 | U0100 | - | - | - | |
| U0123 | - | - | - | ||
| U0126 | - | - | - | ||
| Sub Bus 2 | Network Gateway ECU*1 | U0265 | ○ | ○ | ○ |
| U1002 | ○ | ○ | ○ | ||
| Rear Television Camera Assembly | U0100 | ○ | ○ | ○ | |
| U0126 | ○ | ○ | ○ | ||
| U0129 | ○ | ○ | ○ | ||
| U0131 | ○ | ○ | ○ | ||
| U0140 | ○ | ○ | ○ | ||
| U0163 | ○ | ○ | ○ | ||
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
X: DTC is likely to be output.
▲: DTC is unlikely to be output.
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
| - | Trouble Mode (CAN Bus Line Short Circuit or Short to GND) | ||
|---|---|---|---|
| Sub bus 2 | |||
| Output ECU | Output DTC | CANH - CANL
CANH - Ground short CANL - Ground short |
|
| V Bus | Airbag Sensor Assembly | - | - |
| Air Conditioning Amplifier Assembly | U0100 | - | |
| U0131 | - | ||
| U0142 | - | ||
| U0155 | - | ||
·
Navigation Receiver Assembly*2*4 ·
Radio and Display Receiver Assembly*3*4 |
U0100 | - | |
| U0129 | - | ||
| U0140 | - | ||
| U0155 | - | ||
| U0164 | - | ||
| U1110 | - | ||
| Main Body ECU (Multiplex Network Body ECU)*1 | U0100 | - | |
| U0101 | - | ||
| U0120 | - | ||
| U0151 | - | ||
| U0155 | - | ||
| U0164 | - | ||
| U023A | ○ | ||
| U0327 | - | ||
| Network Gateway ECU*1 | - | - | |
| Clearance Warning ECU Assembly | U0100 | - | |
| U0101 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| ECM | U0100 | - | |
| U0122 | - | ||
| U0123 | - | ||
| U0126 | - | ||
| U1104 | ○ | ||
| Power Steering ECU Assembly | U0100 | - | |
| U0129 | - | ||
| V Bus | Smart Key ECU Assembly (Certification ECU) | U0100 | - |
| U0140 | - | ||
| U0142 | - | ||
| U0155 | - | ||
| Combination Meter Assembly | U0100 | - | |
| U0129 | - | ||
| U0131 | - | ||
| U0142 | - | ||
| U0151 | - | ||
| U0163 | - | ||
| U023A | ○ | ||
| U1104 | ○ | ||
| Steering Sensor | - | - | |
| Brake Actuator Assembly*4 | U0100 | - | |
| U0123 | - | ||
| U0126 | - | ||
| Sub bus 2 | Network Gateway ECU*1 | U0104 | ○ |
| U0233 | ○ | ||
| U023A | ○ | ||
| U0265 | ○ | ||
| U1002 | ○ | ||
| Blind Spot Monitor Sensor RH | U0100 | ○ | |
| U0126 | ○ | ||
| U0129 | ○ | ||
| U0142 | ○ | ||
| Rear Television Camera Assembly | U0100 | ○ | |
| U0126 | ○ | ||
| U0129 | ○ | ||
| U0131 | ○ | ||
| U0140 | ○ | ||
| U0163 | ○ | ||
| U1110 | ○ | ||
| Lane Departure Warning Camera | U0100 | ○ | |
| U0101 | ○ | ||
| U0123 | ○ | ||
| U0129 | ○ | ||
| U0142 | ○ | ||
| U0155 | ○ | ||
| Driving Support ECU Assembly | U0125 | ○ | |
| U0126 | ○ | ||
| U0129 | ○ | ||
| U0142 | ○ | ||
| Sub bus 1 | Main Body ECU (Multiplex Network Body ECU)*1 | U0199 | - |
| U0200 | - | ||
| U0208 | - | ||
| U1002 | - | ||
| Outer Mirror Control ECU Assembly (for Front Passenger Side) | U0142 | - | |
| Outer Mirror Control ECU Assembly (for Driver Side) | U0142 | - | |
| Position Control ECU and Switch Assembly (for Driver Side) | - | - | |
○: Set
-: DTC is not output.
*1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*2: for Navigation Receiver Type
*3: for Radio and Display Type
*4: DTC U0073 may be stored when communication is lost.
CAN BUS WAVEFORMS
This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)
When malfunctions in multiple ECUs are suspected based on the CAN Bus Check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If no problems are found, check the following waveforms.
If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
Wiggle the connector and wire harness to check if the waveform changes.
CAN bus waveforms (Group 1)
Normal waveform
Open in both of the lines (CANH and CANL) of a CAN branch
Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN Bus Check.
Short between the CAN bus lines (CANH and CANL)
Waveforms disappear.
If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.
CAN bus waveforms (reference) (Group 2)
Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
Open in a CAN branch line (CANH)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN Bus Check, or by checking waveform changes when ECUs or sensors are disconnected (disconnecting connectors from the CAN junction connector enables a quick inspection). The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN branch line (CANL)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN Bus Check, or by checking waveform changes when ECUs or sensors are disconnected (disconnecting connectors from the CAN junction connector enables a quick inspection). The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN main bus line (CANH)
Waveforms of ECUs or sensors that are nearer to the DLC3 than the open part are almost normal.
Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.
An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.
Short between a CAN bus line (CANH) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.
Short between a CAN bus line (CANL) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.
DATA SENDING/RECEIVING TABLE
Data sending/receiving table
If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.
| Data Content | Data Detected and Sent by | Data Received by
(Can be Checked in the Data List) |
Data Received by
(Cannot be Checked in the Data List) |
Relevant Data List Item
[Selected System] |
|---|---|---|---|---|
| Accelerator position | ECM | Brake actuator assembly*5 | ·
Airbag sensor assembly ·
Brake actuator assembly*6 ·
Driving support ECU assembly |
·
Accelerator Position [Engine and ECT] ·
Accelerator Opening Angle % [ABS/VSC/TRC]*5 |
| Engine speed | ECM | ·
Power steering ECU assembly ·
Brake actuator assembly*5 ·
Combination meter assembly ·
Smart key ECU assembly (certification ECU) |
·
Airbag sensor assembly ·
Air conditioning amplifier assembly ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Main body ECU (multiplex network body ECU) ·
Brake actuator assembly*6 |
·
Engine Speed [Engine and ECT] ·
Engine Revolution [EMPS] ·
Engine Revolutions [ABS/VSC/TRC]*5 ·
Engine Rpm [Combination Meter] ·
Engine Speed [Starting Control] |
| Engine coolant temperature | ECM | ·
Air conditioning amplifier assembly ·
Combination meter assembly |
Navigation receiver assembly | ·
Coolant Temp [Engine and ECT] ·
Engine Coolant Temp [Air Conditioner] ·
Coolant Temperature [Combination Meter] |
| Vehicle speed | Brake actuator assembly | ·
ECM ·
Power steering ECU assembly ·
Combination meter assembly ·
Blind spot monitor sensor RH ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Rear television camera assembly ·
Driving support ECU assembly |
Airbag sensor assembly | ·
Vehicle Speed [ABS/VSC/TRC] ·
Vehicle Speed [Engine and ECT] ·
Meter Vehicle Velocity [EMPS] ·
Vehicle Speed Meter [Combination Meter] ·
Vehicle Speed [Blind Spot Monitor Master] ·
Vehicle Speed [Navigation System] ·
Wheel Speed Sensor (4wheel) [IPA/Parking Assist Monitor] ·
CCS Vehicle Spd [Radar Cruise] |
| Combination meter assembly *3 | ·
Clearance warning ECU assembly ·
Smart key ECU assembly (certification ECU) ·
Position control ECU and switch assembly (for driver side) |
·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) |
·
Vehicle Speed Meter [Combination Meter] ·
Vehicle Speed Info [Clearance Sonar] ·
Vehicle Speed Signal [Power Source Control] ·
Vehicle Speed [Driver Seat] |
|
| Wheel speed | Brake actuator assembly | - | ·
ECM ·
Power steering ECU assembly ·
Blind spot monitor sensor RH ·
Lane departure warning camera ·
Driving support ECU assembly |
·
FR Wheel Speed [ABS/VSC/TRC] ·
FL Wheel Speed [ABS/VSC/TRC] ·
RR Wheel Speed [ABS/VSC/TRC] ·
RL Wheel Speed [ABS/VSC/TRC] |
| Shift position | ECM | ·
Clearance warning ECU assembly ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Smart key ECU assembly (certification ECU) ·
Brake actuator assembly*5 ·
Blind spot monitor sensor RH ·
Position control ECU and switch assembly (for driver side) |
·
Airbag sensor assembly ·
Combination meter assembly ·
Main body ECU (multiplex network body ECU) ·
Rear television camera assembly ·
Driving support ECU assembly ·
Lane departure warning camera |
·
Neutral Position SW Signal [Engine and ECT] ·
Parking Signal [Clearance Sonar] ·
Reverse Signal [Navigation System] ·
Shift P Signal [Power Source Control] ·
Shift Lever Position [ABS/VSC/TRC]*5 ·
Reverse [Blind Spot Monitor Master] ·
P Switch [Driver Seat] |
| Ambient temperature | Air conditioning amplifier assembly | ·
ECM ·
Combination meter assembly |
·
Main body ECU (multiplex network body ECU) ·
Clearance warning ECU assembly ·
Driving support ECU assembly |
·
Ambient Temp Sensor [Air Conditioner] ·
Ambient Temp for A/C [Engine and ECT] ·
Ambient Temperature [Combination Meter] |
| FR door courtesy | Main body ECU (multiplex network body ECU) | - | ·
Smart key ECU assembly (certification ECU) ·
Combination meter assembly*2 ·
Navigation receiver assembly |
FR Door Courtesy [Main Body] |
| Steering angle sensor | Steering sensor | ·
Power steering ECU assembly ·
Brake actuator assembly*5 ·
Blind spot monitor sensor RH |
·
Airbag sensor assembly ·
Rear television camera assembly ·
Driving support ECU assembly |
·
Steering Angle Velocity [EMPS] ·
Steering Angle Sensor [ABS/VSC/TRC]*5 ·
Steering Angle [Blind Spot Monitor Master] |
| Yaw rate sensor | Airbag sensor assembly | Brake actuator assembly*5 | ·
Lane departure warning camera ·
Driving support ECU assembly |
Yaw Rate Sensor [ABS/VSC/TRC]*5 |
| Deceleration sensor | Airbag sensor assembly | Brake actuator assembly*5 | - | ·
Deceleration Sensor [ABS/VSC/TRC]*5 ·
Deceleration Sensor2 [ABS/VSC/TRC]*5 |
| Turn signal | Combination meter assembly | Blind spot monitor sensor RH | ·
Driving support ECU assembly ·
Lane departure warning camera |
·
Turn Signal Switch (Left) [Combination Meter] ·
Turn Signal Switch (Right) [Combination Meter] ·
Turn Switch State [Blind Spot Monitor Master] |
| Ignition switch condition | Main body ECU (multiplex network body ECU) | Position control ECU and switch assembly (for driver side) | ·
Outer mirror control ECU assembly (for driver side) ·
Outer mirror control ECU assembly (for front passenger side) ·
Smart key ECU assembly (certification ECU) ·
Rear television camera assembly |
·
IG SW [Main Body] ·
Ignition Switch [Driver Seat] |
| Headlight switch | Main body ECU (multiplex network body ECU) | Lane departure warning camera | ·
Air conditioning amplifier assembly ·
Combination meter assembly*2 |
·
Head Light SW (Head) [Main Body] ·
Head Light (High Beam) [Lane Departure Alert] |
| Combination meter assembly power source voltage*1 | Combination meter assembly | - | - | +B Voltage Value [Combination Meter] |
| Power steering ECU assembly power source voltage*1 | Power steering ECU assembly | - | - | IG Power Supply [EMPS] |
| Solar sensor*1*4 | Air conditioning amplifier assembly | - | - | Solar Sensor (D side) [Air Conditioner] |
| Ignition switch condition*1 | Smart key ECU assembly (certification ECU) | - | - | Ignition Switch [Entry&Start] |
| ECM power source voltage*1 | ECM | - | - | Battery Voltage [Engine and ECT] |
| Navigation receiver assembly power source voltage*1 | Navigation receiver assembly | - | - | Battery Voltage [Navigation System] |
| Radio and display receiver assembly power source voltage*1 | Radio and display receiver assembly | - | - | Battery Voltage [Navigation System] |
| Outer mirror control ECU assembly (for driver side) power source voltage*1 | Outer mirror control ECU assembly (for driver side) | - | - | +B Voltage Input Value [Mirror R] |
| Outer mirror control ECU assembly (for front passenger side) power source voltage*1 | Outer mirror control ECU assembly (for front passenger side) | - | - | +B Voltage Input Value [Mirror L] |
| Position control ECU and switch assembly (for driver side) power source voltage*1 | Position control ECU and switch assembly (for driver side) | - | - | Power Voltage [Driver Seat] |
| Blind spot monitor sensor RH power source voltage*1 | Blind spot monitor sensor RH | - | - | Power Supply Voltage [Blind Spot Monitor Master] |
| Clearance sonar main switch*1 | Clearance warning ECU assembly | - | - | Main Switch [Clearance Sonar] |
| Wiper operation status*1 | Driving support ECU assembly | - | - | Wiper Information [Pre-Crash 2] |
*1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.
*2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter.
*3: The combination meter assembly receives a vehicle speed signal from the brake actuator assembly and sends the signal to other ECUs.
*4: for Automatic air conditioning system
*5: w/ VSC
*6: w/o VSC
Details of relevant Data List items (Selected system: Engine and ECT)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N (neutral) or P, the A/C switch should be off and all accessory switches should be off.
Warm up the engine.
Turn the A/C switch off.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. ·
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 610 to 710 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Coolant Temp | Coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Battery Voltage | Battery voltage | Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change. |
| Accelerator Position | Accelerator pedal position | Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%. |
| Neutral Position SW Signal | Park/Neutral position switch status | ON or OFF | ON: Shift lever in P or N | - |
| Ambient Temp for A/C | Ambient temperature for A/C | Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | - |
Details of relevant Data List items (Selected system: ABS/VSC/TRC) (w/o VSC)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Details of relevant Data List items (Selected system: ABS/VSC/TRC) (w/ VSC)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Lever Position | Shift lever position information | ''P,N'', R, D/M, 1st-6th/B or Fail | Actual shift lever position | - |
| Deceleration Sensor | Acceleration sensor reading | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Deceleration Sensor2 | Acceleration sensor 2 reading | Min.: -18.525 m/s2, Max.: 18.387 m/s2 | - | During deceleration/acceleration: Changes continuously |
| Yaw Rate Sensor | Yaw rate sensor | Min.: -128 °/s, Max.: 127 °/s | Vehicle stopped: 0 °/s
Turning right: -128 to 0 °/s Turning left: 0 to 127 °/s |
- |
| Steering Angle Sensor | Steering angle sensor | Min.: -3276.8°, Max.: 3276.7° | Turning left: Increases
Turning right: Decreases |
- |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Engine Revolutions | Engine speed | Min.: 0 rpm, Max.: 65535 rpm | Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%, Max.: 128.0% | When the accelerator pedal is released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
Details of relevant Data List items (Selected system: EMPS)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Meter Vehicle Velocity | Vehicle speed from meter | Min.: 0.0 km/h (0.0mph)
Max.: 300.0 km/h (186.4 mph) |
·
Engine running and vehicle stopped: 0 km/h (0 mph) ·
Engine running and vehicle driven at a constant speed: No significant fluctuation |
- |
| Engine Revolution | Engine speed | Min.: 0 rpm
Max.: 12800 rpm |
Engine running at a constant speed: No significant fluctuation | - |
| Steering Angle Velocity | Steering angle speed | Min.: -32768 deg/s
Max.: 32767 deg/s |
Engine running and steering wheel being turned: Value changes in proportion to steering speed
-The value increases when turning left and decreases when turning right |
- |
| IG Power Supply | IG power source voltage/ | Min.: 0.0000 V
Max.: 20.1531 V |
Ignition switch ON: 9 to 16 V | - |
Details of relevant Data List items (Selected system: Navigation System)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Navigation System / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Battery Voltage | Battery voltage | Min.: 0 V, Max.:24 V | 11 to 14 V | - |
| Reverse Signal | Reverse Signal | ON or OFF | ON: Shift lever in R
OFF: Shift lever in any position other than R |
- |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Details of relevant Data List items (Selected system: Entry&Start)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
When using the GTS with the ignition switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ignition Switch | Certification ECU (smart key ECU assembly) IG power supply input status | ON or OFF | ON: Engine switch ON
OFF: Engine switch off |
When the engine switch is on (ACC), OFF is displayed. |
Details of relevant Data List items (Selected system: Power Source Control)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | Shift position P | ON or OFF | ON: Shift lever in P
OFF: Shift lever not in P |
·
Use this item to determine if the shift position switch is malfunctioning. ·
The engine cannot be started when this item is OFF. |
| Vehicle Speed Signal | Vehicle being driven or stopped | Stop or Run | Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more |
- |
Details of relevant Data List items (Selected system: Starting Control)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Starting Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | 0 to 16383 r/min | Fluctuates in accordance with engine speed | - |
Details of relevant Data List items (Selected system: Combination Meter)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Combination Meter / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Engine Rpm | Engine speed | Min.: 0 rpm, Max.: 12750 rpm | Almost the same as actual engine speed | - |
| Coolant Temperature | Engine coolant temperature | Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) | After warming up: 75 to 100°C (167 to 212°F) | - |
| +B Voltage Value | Battery voltage | Min.: 0 V, Max.: 25.5 V | 11 to 14 V | - |
| Ambient Temperature | Outside temperature | Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) | Almost the same as actual outside temperature | The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F) |
| Turn Signal Switch (Right) | RH turn signal switch | OFF or ON | OFF: RH turn switch off
ON: RH turn switch on |
- |
| Turn Signal Switch (Left) | LH turn signal switch | OFF or ON | OFF: LH turn switch off
ON: LH turn switch on |
- |
Details of relevant Data List items (Selected system: Air Conditioner) (for Manual air conditioning system)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ambient Temp Sensor | Ambient temperature sensor (Thermistor assembly) | Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F) |
Actual ambient temperature displayed | - |
| Engine Coolant Temp | Engine coolant temperature sensor | Min.: 1.30°C (34.34°F)
Max.: 90.55°C (194.99°F) |
Actual engine coolant temperature displayed | - |
Details of relevant Data List items (Selected system: Air Conditioner) (for Automatic air conditioning system)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ambient Temp Sensor | Ambient temperature sensor (thermistor assembly) | Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F) |
Actual ambient temperature displayed | - |
| Solar Sensor (D Side) | Driver side automatic light control sensor (solar sensor) | Min.: 0
Max.: 255 |
Driver side automatic light control sensor (solar sensor) value increases as brightness increases | - |
| Engine Coolant Temp | Engine coolant temperature sensor | Min.: 1.30°C (34.34°F)
Max.: 90.55°C (194.99°F) |
Actual engine coolant temperature displayed | - |
Details of relevant Data List items (Selected system: Main Body)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IG SW | Engine switch status | ON or OFF | ON: Engine switch on (IG)
OFF: Engine switch off |
- |
| FR Door Courtesy | Front RH door courtesy light switch signal | ON or OFF | ON: Front RH door closed
OFF: Front RH door open |
- |
| Head Light SW (Head) | Light control switch head position signal | ON or OFF | ON: Light control switch in head position
OFF: Light control switch not in head position |
- |
Details of relevant Data List items (Selected system: Blind Spot Monitor Master)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Blind Spot Monitor Master / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Switch State | Master side, slave side state of the turn SW | Left ON, Right ON or OFF | Left ON: Left turn switch on
Right ON: Right turn switch on OFF: Switch not operated |
- |
| Reverse (Only for AT/CVT) | State of the Shift Position R Signal | OFF or ON | ON: Shift lever in R
OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal | Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor | Min.: -3072°, Max.: 3070.5° | Left turn: Increase
Right turn: Decrease |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 50 V | Always: 11 to 14 V | - |
Details of relevant Data List items (Selected system: Driver Seat)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ignition Switch | Communication state of ignition switch signal | ON or OFF | ON: Ignition switch to ON signal received
OFF: Ignition switch off signal not received |
- |
| P Switch | Park state signal | ON or OFF | ON: Shift lever in P
OFF: Shift lever in a position other than P |
- |
| Vehicle Speed | Vehicle speed data | min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| Power Voltage | Power supply for position control ECU and switch assembly | min: 0.95 V, max: 20.84 V | Within range from 11 V to 14 V | - |
Details of relevant Data List items (Selected system: Mirror L)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Mirror L / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 19.98 V | Within range from 11 to 14 V | - |
Details of relevant Data List items (Selected system: Mirror R)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Mirror R / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 19.98 V | Within range from 11 to 14 V | - |
Details of relevant Data List items (Selected system: IPA/Parking Assist Monitor)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / IPA/Parking Assist Monitor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wheel Speed Sensor (4wheel) | Vehicle speed signal from speed sensor | OK or NG | OK: Speed signal normal
NG: Speed signal abnormal |
- |
Details of relevant Data List items (Selected system: Pre-Crash 2)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper Information | Wiper operational status | Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo or Hi | The respective operational status displayed | - |
Details of relevant Data List items (Selected system: Clearance Sonar)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Clearance Sonar / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Main Switch | Back sonar or clearance sonar switch assembly | OFF or ON | OFF: Back Sonar or Clearance Sonar Switch Assembly off
ON: Back Sonar or Clearance Sonar Switch Assembly on |
- |
| Parking Signal | Parking signal | OFF or ON | OFF: Shift lever in any position other than P
ON: Shift lever in P |
- |
| Vehicle Speed Info | Vehicle speed signal | Snr Stop or Snr Work | Snr Stop: Vehicle speed approximately 13 km/h (8.1 mph) or more (when accelerating) or approximately 9 km/h (5.6 mph) or more (when decelerating)
Snr Work: Vehicle speed less than approximately 13 km/h (8.1 mph) (when accelerating) or less than approximately 9 km/h (5.6 mph) (when decelerating) |
- |
Details of relevant Data List items (Selected system: Lane Departure Alert)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Lane Departure Alert / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Head Light (High Beam) | Status of the head light (high beam) | OFF or ON | ON: Headlight dimmer switch HI
OFF: Headlight dimmer switch except HI |
- |
Details of relevant Data List items (Selected system: Radar Cruise)
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Radar Cruise / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| CCS Vehicle Spd | Vehicle speed sensor | min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) | Actual vehicle speed | - |