Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ VSC) › from 2015.04
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074148 AIRBAG SYSTEM(w/ VSC) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC)  SRS Warning Light does not Come ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

If a malfunction occurs in the airbag sensor assembly, combination meter assembly or wire harness connected to the airbag sensor assembly or combination meter assembly, the SRS warning light comes on.

When terminals TC and CG of the DLC3 are connected, DTCs are displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly via CAN communication.

WIRING DIAGRAM

C308903E01
5.99,3.385 6.448,3.646 0.458,0.26 10 false I47 6,3.552 6.938,4.052 0.938,0.5 10 false Airbag Sensor Assembly 5.823,2.833 6.281,3.094 0.458,0.26 10 false 26 6.042,2.938 6.5,3.198 0.458,0.26 10 false E2 5.823,2.323 6.281,2.583 0.458,0.26 10 false 25 6.042,2.417 6.5,2.677 0.458,0.26 10 false E1 5.823,1.729 6.281,1.99 0.458,0.26 10 false 22 6.042,1.875 6.5,2.135 0.458,0.26 10 false CANL 5.823,1.177 6.281,1.438 0.458,0.26 10 false 13 6.042,1.323 6.5,1.583 0.458,0.26 10 false CANH 5.823,0.552 6.281,0.813 0.458,0.26 10 false 21 6.042,0.646 6.5,0.906 0.458,0.26 10 false IG2 5.125,0.771 5.583,1.031 0.458,0.26 10 false A/B 2.667,0.25 4.063,0.51 1.396,0.26 10 false from Ignition Switch*1 2.938,0.635 4.333,0.896 1.396,0.26 10 false from IG2 Relay*2 4.073,1.177 4.844,1.448 0.771,0.271 10 false 16*3, 17*4 4.083,1.729 4.99,1.958 0.906,0.229 10 false 15*3, 16*4 3.635,1.323 4.094,1.583 0.458,0.26 10 false CANH 3.656,1.875 4.115,2.135 0.458,0.26 10 false CANL 3.104,1.313 3.563,1.573 0.458,0.26 10 false IG+ 3.104,1.875 3.563,2.135 0.458,0.26 10 false B 3.104,2.427 3.563,2.688 0.458,0.26 10 false ES 3.063,2.927 3.521,3.188 0.458,0.26 10 false I18 3.063,3.094 4.25,3.583 1.188,0.49 10 false Combination Meter Assembly 2.875,1.229 3.333,1.49 0.458,0.26 10 false 13 2.948,1.792 3.406,2.052 0.458,0.26 10 false 1 2.469,2.333 3.365,2.646 0.896,0.313 10 false 7*3, 20*4 1.781,1.458 2.615,1.771 0.833,0.313 10 false METER-IG2 1.75,2.01 2.688,2.323 0.938,0.313 10 false ECU-B NO. 1 0.25,1.323 1.385,1.656 1.135,0.333 10 false from IG2 Relay 0.417,1.875 1.24,2.271 0.823,0.396 10 false from Battery 0.219,3.292 2.646,3.583 2.427,0.292 10 false *1: w/o Smart Entry and Start System 0.219,3.552 2.698,3.906 2.479,0.354 10 false *2: w/ Smart Entry and Start System 0.219,3.865 2.698,4.219 2.479,0.354 10 false *3: w/o Multi-information Display 0.219,4.177 2.698,4.531 2.479,0.354 10 false *4: w/ Multi-information Display 0.729,4.5 2.781,4.719 2.052,0.219 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR

NG

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the combination meter assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

3.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
C126720C09
0.125,0.406 0.479,0.635 0.354,0.229 0.844,1.365 0.51,1.552 false 0.833,1.125 0.5,0.927 false 1.938,1.396 2.615,1.906 false 1.781,1.104 2.615,0.344 false 0.094,0.052 0.354,0.323 0.26,0.271 10 false *a 0.25,1.479 0.698,1.813 0.448,0.333 10 false IG+ 2.656,1.833 3.063,2.063 0.406,0.229 10 false ES*B 0.375,0.833 0.698,1.135 0.323,0.302 10 false B 0.219,0.438 0.667,0.729 0.448,0.292 10 false I18 2.646,0.26 3.271,2.063 0.625,1.802 10 false ES*A
*A w/o Multi-information Display
*B w/ Multi-information Display
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I18-13 (IG+) - Body ground Ignition switch ON 11 to 14 V
I18-1 (B) - Body ground Always 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Multi-information Display:
Tester Connection Condition Specified Condition
I18-7 (ES) - Body ground Always Below 1 Ω

w/ Multi-information Display:
Tester Connection Condition Specified Condition
I18-20 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE WIRE HARNESS

4.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Disconnect the connector from the airbag sensor assembly.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then comes back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY