Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074080 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and also the radio receiver assembly itself cannot function.

WIRING DIAGRAM

E314735E01
6.104,4.292 7.073,4.854 0.969,0.563 10 false Radio Receiver Assembly 6.031,4.104 6.646,4.302 0.615,0.198 10 false I150 4.656,4.167 5.677,4.677 1.021,0.51 10 false Spiral Cable Sub-assembly 1.208,5.729 3.344,6.26 2.135,0.531 10 false Steering Pad Switch Assembly 1.448,2.948 2.458,3.219 1.01,0.271 10 false MODE/HOLD 1.771,4.573 2.438,4.958 0.667,0.385 10 false Off hook* 2.615,4.573 3.323,4.938 0.708,0.365 10 false On hook* 0.271,1.385 0.948,1.75 0.677,0.365 10 false Volume- 1.031,1.396 1.781,1.76 0.75,0.365 10 false Volume+ 1.969,1.375 2.542,1.802 0.573,0.427 10 false Seek- 2.74,1.396 3.458,1.719 0.719,0.323 10 false Seek+ 6.25,0.802 6.854,1.083 0.604,0.281 10 false SW1 6.26,1.99 6.865,2.271 0.604,0.281 10 false SWG 6.271,3.583 6.875,3.865 0.604,0.281 10 false SW2 4.948,3.479 5.385,3.76 0.438,0.281 10 false AU2 5,1.885 5.448,2.177 0.448,0.292 10 false EAU 4.99,0.667 5.469,0.99 0.479,0.323 10 false AU1 5.552,0.813 6.156,1.094 0.604,0.281 10 false I28 5.594,1.792 5.927,2.083 0.333,0.292 10 false 3 5.573,0.594 5.948,0.896 0.375,0.302 10 false 6 5.583,3.385 5.948,3.625 0.365,0.24 10 false 5 6.021,3.469 6.406,3.75 0.385,0.281 10 false 22 6.042,1.865 6.302,2.135 0.26,0.271 10 false 23 6.021,0.688 6.469,0.958 0.448,0.271 10 false 21 4.531,3.583 5.135,3.865 0.604,0.281 10 false z3 4.563,1.99 5.167,2.271 0.604,0.281 10 false z3 4.573,0.792 5.177,1.073 0.604,0.281 10 false z3 5.552,2 6.156,2.281 0.604,0.281 10 false I28 5.573,3.573 6.177,3.854 0.604,0.281 10 false I28 4.552,0.604 5,0.875 0.448,0.271 10 false 11 4.573,1.792 5.021,2.063 0.448,0.271 10 false 8 4.542,3.375 4.99,3.646 0.448,0.271 10 false 10 5.729,6.292 7.156,6.844 1.427,0.552 10 false *: w/ Microphone

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PRECAUTION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the I150 radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-21 (SW1) - I150-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
I150-22 (SW2) - I150-23 (SWG) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed* 313 to 345 Ω
Off hook switch pushed* 950 to 1050 Ω

*: w/ Microphone



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E314604C02
1.771,2.385 1.406,2.135 false 1.74,2.625 1.292,2.813 false 1.938,3.063 1.875,3.531 false 2.104,2.719 1.24,3.208 false 2.771,2.281 2.115,2.354 false 5.063,2.365 5.448,1.604 false 5.417,3.5 5.042,2.708 false 3.417,1.031 2.969,1.313 false 4.271,1.646 3.635,1.01 false 4.323,1.396 3.75,1.021 false 0.208,0.167 0.521,0.323 0.313,0.156 10 false *a 1.229,2.01 1.542,2.167 0.313,0.156 10 false *b 1.125,2.719 1.438,2.875 0.313,0.156 10 false *c 1.083,3.167 1.396,3.323 0.313,0.156 10 false *d 2.823,2.198 3.135,2.354 0.313,0.156 10 false *e 1.833,3.583 2.146,3.74 0.313,0.156 10 false *f 5.469,1.438 5.677,1.75 0.208,0.313 10 false *g 5.406,3.521 5.719,3.677 0.313,0.156 10 false *h 4.417,1.313 4.875,1.51 0.458,0.198 10 false AU1 2.656,1.271 3.115,1.469 0.458,0.198 10 false EAU 4.323,1.573 4.781,1.771 0.458,0.198 10 false AU2 5.646,1.458 6.104,1.656 0.458,0.198 10 false *A 5.583,3.521 6.042,3.719 0.458,0.198 10 false *A
*A w/ Microphone - -
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Seek-
*e Seek+ *f MODE/HOLD
*g Off hook *h On hook


Standard Resistance:
Tester Connection Condition Specified Condition
11 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
10 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed* 313 to 345 Ω
Off hook switch pushed* 950 to 1050 Ω

*: w/ Microphone



Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.
E263757C13
1.323,0.583 1.625,0.813 0.302,0.229 0.458,3.833 0.76,4.063 0.302,0.229 1.656,0.969 2.021,0.74 false 2,0.969 2.135,0.75 false 2.677,0.979 2.365,0.74 false 0.854,4.229 1.188,3.875 false 1.5,4.24 1.427,3.875 false 1.865,4.229 1.51,3.865 false 0.24,0.188 0.552,0.385 0.313,0.198 10 *a 1.25,0.313 1.563,0.51 0.313,0.198 10 *b 0.365,3.573 0.677,3.771 0.313,0.198 10 *c 1.417,0.615 1.729,0.813 0.313,0.198 10 z3 0.531,3.875 0.99,4.073 0.458,0.198 10 I28 1.469,0.99 1.927,1.188 0.458,0.198 10 AU1 1.865,0.99 2.323,1.188 0.458,0.198 10 AU2 2.531,1 2.99,1.198 0.458,0.198 10 EAU 0.698,4.25 1.052,4.458 0.354,0.208 10 EAU 1.344,4.24 1.802,4.438 0.458,0.198 10 AU2 1.76,4.24 2.219,4.438 0.458,0.198 10 AU1
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-8 (EAU) - I28-3 (EAU) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z3-11 (AU1) - I28-6 (AU1) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z3-10 (AU2) - I28-5 (AU2) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-8 (EAU) - I28-3 (EAU) Always 3 Ω or less
z3-11 (AU1) - I28-6 (AU1) Always 3 Ω or less
z3-10 (AU2) - I28-5 (AU2) Always 3 Ω or less


NOTICE:
·

Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO RECEIVER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the I150 radio receiver assembly connector.


b.

Disconnect the I28 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-23 (SWG) - I28-3 (EAU) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)