Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1507 Open in Turn Signal Circuit When IG voltage is 9.5 V or more and the following condition is detected:
1.

Open in turn signal light circuit


·

Harness or connector

·

Bulb

·

Instrument panel junction block assembly

·

Outer mirror control ECU assembly LH*

·

Outer mirror control ECU assembly RH*

·

Combination meter assembly


DTC stored -
B1508 Short in Turn Signal / Hazard Flasher Circuit When IG voltage is 9.5 V or more and the following condition is detected:
1.

Short in turn signal light circuit or hazard warning light circuit


·

Harness or connector

·

Bulb

·

Instrument panel junction block assembly

·

Outer mirror control ECU assembly LH*

·

Outer mirror control ECU assembly RH*

·

Combination meter assembly


DTC stored -

*: w/ Seat Position Memory


WIRING DIAGRAM

w/o Seat Position Memory


E309047E04
4.719,0.615 5.031,0.813 0.313,0.198 10 false 3A 3.104,0.615 3.417,0.813 0.313,0.198 10 false 3D 3.094,0.427 3.406,0.625 0.313,0.198 10 false 10 4.729,0.406 5.042,0.604 0.313,0.198 10 false 20 3.115,1.604 3.427,1.802 0.313,0.198 10 false 3C 3.125,1.396 3.438,1.594 0.313,0.198 10 false 22 3.104,2.615 3.417,2.813 0.313,0.198 10 false 3A 3.115,2.406 3.427,2.604 0.313,0.198 10 false 40 3.115,3.531 3.427,3.729 0.313,0.198 10 false 3D 3.156,3.344 3.469,3.542 0.313,0.198 10 false 5 3.104,4.552 3.417,4.75 0.313,0.198 10 false 3C 3.104,4.365 3.417,4.563 0.313,0.198 10 false 19 3.104,5.573 3.417,5.771 0.313,0.198 10 false 3B 3.115,5.385 3.427,5.583 0.313,0.198 10 false 32 3.219,5.99 4.813,6.385 1.594,0.396 10 false Instrument Panel Junction Block Assembly 4.719,3.531 5.031,3.729 0.313,0.198 10 false 3A 4.708,3.333 5.021,3.531 0.313,0.198 10 false 37 5.875,0.51 6.188,0.708 0.313,0.198 10 false 7 6.063,0.594 6.375,0.792 0.313,0.198 10 false LL 6.052,3.531 6.365,3.729 0.313,0.198 10 false LR 5.802,3.427 6.115,3.625 0.313,0.198 10 false 13 5.344,5.813 5.656,6.01 0.313,0.198 10 false I17 5.323,5.969 7.156,6.198 1.833,0.229 10 false Combination Meter Assembly 0.604,5.813 0.917,6.01 0.313,0.198 10 false J14 0.583,5.958 3.031,6.167 2.448,0.208 10 false Side Turn Signal Light Assembly RH 0.927,5.479 1.188,5.677 0.26,0.198 10 false 5 1.125,5.479 1.438,5.677 0.313,0.198 10 false E 2.104,5.479 2.417,5.677 0.313,0.198 10 false B 2.271,5.479 2.583,5.677 0.313,0.198 10 false 2 0.552,4.74 0.865,4.938 0.313,0.198 10 false T13 0.552,4.906 2.958,5.094 2.406,0.188 10 false Rear Combination Light Assembly RH 0.958,4.448 1.271,4.646 0.313,0.198 10 false 2 1.135,4.448 1.448,4.646 0.313,0.198 10 false E 2.083,4.458 2.396,4.656 0.313,0.198 10 false B 2.271,4.458 2.583,4.656 0.313,0.198 10 false 1 0.906,3.938 1.219,4.135 0.313,0.198 10 false A85 0.958,3.448 1.271,3.646 0.313,0.198 10 false 3 1.125,3.448 1.438,3.646 0.313,0.198 10 false E 2.104,3.448 2.417,3.646 0.313,0.198 10 false B 2.281,3.448 2.594,3.646 0.313,0.198 10 false 4 0.552,2.823 1.031,3.063 0.479,0.24 10 false K13 0.552,2.979 2.979,3.198 2.427,0.219 10 false Side Turn Signal Light Assembly LH 0.938,2.51 1.25,2.708 0.313,0.198 10 false 5 1.125,2.51 1.438,2.708 0.313,0.198 10 false E 2.104,2.51 2.417,2.708 0.313,0.198 10 false B 2.271,2.51 2.583,2.708 0.313,0.198 10 false 2 0.583,1.792 0.896,1.99 0.313,0.198 10 false T8 0.583,1.958 3.063,2.125 2.479,0.167 10 false Rear Combination Light Assembly LH 0.958,1.5 1.271,1.698 0.313,0.198 10 false 2 1.115,1.5 1.427,1.698 0.313,0.198 10 false E 2.104,1.5 2.417,1.698 0.313,0.198 10 false B 2.292,1.5 2.604,1.698 0.313,0.198 10 false 1 0.865,1 1.531,1.281 0.667,0.281 10 false A86 1.188,1.01 3.896,1.229 2.708,0.219 10 false Headlight Assembly LH 0.948,0.521 1.26,0.719 0.313,0.198 10 false 3 1.125,0.521 1.438,0.719 0.313,0.198 10 false E 2.083,0.521 2.396,0.719 0.313,0.198 10 false B 2.292,0.521 2.604,0.719 0.313,0.198 10 false 4 1.219,3.938 3.927,4.156 2.708,0.219 10 false Headlight Assembly RH


w/ Seat Position Memory



E237287E19
3.646,7.115 5.25,7.75 1.604,0.635 10 false Instrument Panel Junction Block Assembly 0.771,0.875 2.365,1.031 1.594,0.156 10 false Headlight Assembly LH 0.781,0.719 1.146,0.969 0.365,0.25 10 false A86 0.635,1.823 3.052,2.146 2.417,0.323 10 false Rear Combination Light Assembly LH 0.646,1.677 0.938,1.854 0.292,0.177 10 false T8 0.24,3.365 1.615,3.75 1.375,0.385 10 false Side Turn Signal Light Assembly LH 0.781,4.573 2.948,4.896 2.167,0.323 10 false Headlight Assembly RH 0.792,4.438 1.083,4.615 0.292,0.177 10 false A85 0.583,5.573 2.969,5.896 2.385,0.323 10 false Rear Combination Light Assembly RH 0.583,5.438 0.938,5.656 0.354,0.219 10 false T13 2.969,6.229 3.365,6.406 0.396,0.177 10 false J13 1.677,6.219 2.073,6.396 0.396,0.177 10 false z7 5.792,7.146 7.021,7.479 1.229,0.333 10 false Combination Meter Assembly 5.781,6.979 6.073,7.156 0.292,0.177 10 false I17 5.156,4.177 5.604,4.542 0.448,0.365 10 false 3A 5.156,4 5.396,4.208 0.24,0.208 10 false 37 5.156,0.49 5.427,0.75 0.271,0.26 10 false 3A 5.167,0.302 5.5,0.604 0.333,0.302 10 false 20 3.479,4.177 3.677,4.354 0.198,0.177 10 false 3D 3.521,4 3.719,4.177 0.198,0.177 10 false 5 3.479,0.479 3.823,0.76 0.344,0.281 10 false 3D 3.479,0.302 3.76,0.531 0.281,0.229 10 false 10 3.479,1.469 3.677,1.646 0.198,0.177 10 false 3C 3.5,1.281 3.698,1.458 0.198,0.177 10 false 22 3.479,5.208 3.677,5.385 0.198,0.177 10 false 3C 3.479,5.031 3.656,5.208 0.177,0.177 10 false 19 5.813,4.063 6.167,4.406 0.354,0.344 10 false 13 5.875,0.375 6.073,0.552 0.198,0.177 10 false 7 6.063,4.177 6.458,4.521 0.396,0.344 10 false LR 6.083,0.479 6.281,0.656 0.198,0.177 10 false LL 2.083,1.365 2.344,1.688 0.26,0.323 10 false B 2.083,5.094 2.219,5.271 0.135,0.177 10 false B 1.135,1.365 1.448,1.542 0.313,0.177 10 false E 1.125,5.094 1.438,5.271 0.313,0.177 10 false E 2.302,1.354 2.615,1.531 0.313,0.177 10 false 1 0.969,1.365 1.292,1.708 0.323,0.344 10 false 2 2.302,0.385 2.615,0.563 0.313,0.177 10 false 4 0.948,0.375 1.24,0.688 0.292,0.313 10 false 3 2.281,5.094 2.594,5.271 0.313,0.177 10 false 1 0.958,5.094 1.177,5.375 0.219,0.281 10 false 2 2.292,4.073 2.604,4.25 0.313,0.177 10 false 4 0.958,4.073 1.115,4.25 0.156,0.177 10 false 3 2.104,0.385 2.427,0.719 0.323,0.333 10 false B 1.135,0.375 1.271,0.552 0.135,0.177 10 false E 3.479,2.458 3.833,2.75 0.354,0.292 10 false 3A 3.49,2.281 3.75,2.49 0.26,0.208 10 false 40 1.979,3.01 2.333,3.188 0.354,0.177 10 false TRN- 2.552,3.01 2.906,3.188 0.354,0.177 10 false GND 1.979,2.5 2.406,2.677 0.427,0.177 10 false TRN+ 2.542,2.5 2.896,2.677 0.354,0.177 10 false TRNI 1.979,6.75 2.333,6.927 0.354,0.177 10 false TRN- 2.552,6.75 2.906,6.927 0.354,0.177 10 false GND 1.969,6.25 2.396,6.427 0.427,0.177 10 false TRN+ 2.542,6.25 2.896,6.427 0.354,0.177 10 false TRNI 1.677,6.052 1.99,6.229 0.313,0.177 10 false 16 1.677,6.74 2.073,6.917 0.396,0.177 10 false z7 1.708,6.573 2.021,6.75 0.313,0.177 10 false 8 3,6.042 3.313,6.219 0.313,0.177 10 false 11 2.979,6.75 3.375,6.927 0.396,0.177 10 false J13 3.052,6.563 3.365,6.74 0.313,0.177 10 false 7 2.948,2.469 3.344,2.646 0.396,0.177 10 false K12 1.677,2.469 2.073,2.646 0.396,0.177 10 false z6 1.677,2.302 1.99,2.479 0.313,0.177 10 false 16 1.688,2.99 1.917,3.167 0.229,0.177 10 false z6 1.719,2.813 2.063,3.01 0.344,0.198 10 false 8 3,2.292 3.313,2.469 0.313,0.177 10 false 11 2.948,3 3.344,3.177 0.396,0.177 10 false K12 3.042,2.823 3.354,3 0.313,0.177 10 false 7 2.094,4.073 2.344,4.365 0.25,0.292 10 false B 1.135,4.063 1.271,4.24 0.135,0.177 10 false E 0.167,7.115 1.573,7.573 1.406,0.458 10 false Side Turn Signal Light Assembly RH 1.844,7.125 3.094,7.5 1.25,0.375 10 false Outer Mirror Control ECU Assembly RH 1.823,3.354 3.073,3.75 1.25,0.396 10 false Outer Mirror Control ECU Assembly LH 3.479,6.219 3.677,6.396 0.198,0.177 10 false 3B 3.49,6.031 3.979,6.438 0.49,0.406 10 false 32

CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs for this system before performing the following procedure.


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Turn signal lights for one side do not illuminate. A
Front turn signal light does not illuminate. B
Rear turn signal light does not illuminate. C
Side turn signal light does not illuminate. (w/o Seat Position Memory) D
Side turn signal light does not illuminate. (w/ Seat Position Memory) E



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

D

5.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

E

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
I17-7 (LL) - 3A-20 Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
I17-13 (LR) - 3A-37 Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
I17-7 (LL) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
I17-13 (LR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A86*1 or A85*2 headlight assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A86-4 (B) - 3D-10 Always Below 1 Ω
A86-3 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A85-4 (B) - 3D-5 Always Below 1 Ω
A85-3 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A86-4 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A85-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the T8*1 or T13*2 rear combination light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
T8-1 (B) - 3C-22 Always Below 1 Ω
T8-2 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
T13-1 (B) - 3C-19 Always Below 1 Ω
T13-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
T8-1 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
T13-1 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the K13*1 or J14*2 side turn signal light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 3A and 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
K13-2 (B) - 3A-40 Always Below 1 Ω
K13-5 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
J14-2 (B) - 3B-32 Always Below 1 Ω
J14-5 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
K13-2 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
J14-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E225578C03
5.042,0.198 5.458,0.448 0.417,0.25 2,0.177 2.417,0.427 0.417,0.25 5.042,1.542 5.458,1.792 0.417,0.25 2,1.542 2.417,1.792 0.417,0.25 0.292,0.167 0.604,0.365 0.313,0.198 10 false *a 2.125,1.594 2.438,1.792 0.313,0.198 10 false 3B 5.167,1.594 5.479,1.792 0.313,0.198 10 false 3C 5.177,0.25 5.49,0.448 0.313,0.198 10 false 3D 2.125,0.229 2.438,0.427 0.313,0.198 10 false 3A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-20 - 3D-10 Always Below 1 Ω
3A-20 - 3C-22 Always Below 1 Ω
3A-20 - 3A-40 Always Below 1 Ω
3A-37 - 3D-5 Always Below 1 Ω
3A-37 - 3C-19 Always Below 1 Ω
3A-37 - 3B-32 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the K12*1 or J13*2 outer mirror control ECU assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 3A and 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
K12-11 (TRNI) - 3A-40 Always Below 1 Ω
K12-7 (GND) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
J13-11 (TRNI) - 3B-32 Always Below 1 Ω
J13-7 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
K12-11 (TRNI) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
J13-11 (TRNI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY
a.

Replace the outer mirror control ECU assembly with a new or a known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL



Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

END

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY