Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0129  Lost Communication with Skid Control ECU  U0131  Lost Communication with Power Steering Control Module  U0142  Lost Communication with Main Body ECU  U0151  Lost Communication with Airbag ECU  U0163  Lost Communication with Navigation Control Module  U023A  Lost Communication with Front Camera Module  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The combination meter assembly communicates with the ECM, brake actuator assembly (skid control ECU), power steering ECU assembly, main body ECU (multiplex network body ECU), airbag sensor assembly, navigation receiver assembly*1, lane departure warning camera*2 and driving support ECU assembly*3 via CAN communication.

*1: for Navigation Receiver Type

*2: w/ Lane Departure Alert System

*3: w/ Pre-crash Safety System


DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
U0100 Lost Communication with ECM / PCM "A" When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with ECM continues for 2 seconds or more


·

ECM

·

CAN communication system

·

Combination meter assembly


DTC stored -
U0129 Lost Communication with Skid Control ECU When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with brake actuator assembly (skid control ECU) continues for 2 seconds or more


·

Brake actuator assembly (Skid control ECU)

·

CAN communication system

·

Combination meter assembly


DTC stored -
U0131 Lost Communication with Power Steering Control Module When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with power steering ECU assembly continues for 3 seconds or more


·

Power steering ECU assembly

·

CAN communication system

·

Combination meter assembly


DTC stored -
U0142 Lost Communication with Main Body ECU When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with main body ECU (multiplex network body ECU) continues for 3 seconds or more


·

Main body ECU (Multiplex network body ECU)

·

CAN communication system

·

Combination meter assembly


DTC stored -
U0151 Lost Communication with Airbag ECU When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with airbag sensor assembly continues for 10 seconds or more


·

Airbag sensor assembly

·

CAN communication system

·

Combination meter assembly


DTC stored -
U0163 Lost Communication with Navigation Control Module When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with navigation receiver assembly continues for 3 seconds or more


·

Navigation receiver assembly

·

CAN communication system

·

Combination meter assembly


DTC stored for Navigation Receiver Type
U023A Lost Communication with Front Camera Module When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with lane departure warning camera continues for 10 seconds or more


·

Lane departure warning camera

·

CAN communication system

·

Combination meter assembly


DTC stored w/ Lane Departure Alert System
U1104 Lost Communication with Driving Support ECU When IG voltage is 9.5 V or more and the following condition is detected:
1.

No communication with driving support ECU assembly continues for 10 seconds or more


·

Driving support ECU assembly

·

CAN communication system

·

Combination meter assembly


DTC stored w/ Pre-crash Safety System

PROCEDURE

1.CONFIRM DTC OUTPUT
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are output. A
CAN communication DTCs are not output. B



A

B