Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.04–2016.05
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Economy Meter Malfunction  


DESCRIPTION

The combination meter assembly communicates with the ECM and skid control ECU via the CAN communication system. The combination meter calculates the current fuel consumption based on a vehicle speed signal from the skid control ECU, a fuel injection signal from the ECM.

WIRING DIAGRAM

E224308E04
0.604,1.74 2.406,1.896 1.802,0.156 10 false ECM 0.24,3.979 1.813,4.333 1.573,0.354 10 false Brake Actuator Assembly (Skid Control ECU) 3.083,4.438 5.458,4.76 2.375,0.323 10 false : CAN Communication Line 5.302,3.833 7.125,4.271 1.823,0.438 10 false Combination Meter Assembly

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.PERFORM ACTIVE TEST USING GTS (FUEL CONSUMPTION METER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (FUEL CONSUMPTION METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Consumption Meter Operation Fuel consumption meter OFF, MIN, 1/4, 1/2, 3/4, MAX -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Consumption Meter Operation
50004 122 30
OK:

Needle indication is normal.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (VEHICLE SPEED, INJECTION VOLUM)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING GTS (VEHICLE SPEED, INJECTION VOLUM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.


ii.

for Engine and ECT: Powertrain / Engine and ECT / Data List.



e.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Injection Volum (Cylinder1) Injection volume (cylinder 1) Min.: 0 ml, Max.: 2.047 ml 0 to 0.5 ml
·

Idling (engine warmed up): 0.108 ml

·

Running without load (3000 rpm): 0.097 ml


·

Stored as Freeze Frame Data: Yes

·

This is the fuel injection volume for 10 injections.


Chassis > ABS/VSC/TRC > Data List
Tester Display
Vehicle Speed
50003 105 42
Powertrain > Engine and ECT > Data List
Tester Display
Injection Volum (Cylinder1)
50003 234 260

Result:
Result Proceed to
The data list values displayed on the GTS are within the normal condition range. A
The data list value displayed on the GTS differs from the normal condition range. (ABS/VSC/TRC) (w/ VSC) B
The data list value displayed on the GTS differs from the normal condition range. (ABS/VSC/TRC) (w/o VSC) C
The data list value displayed on the GTS differs from the normal condition range. (Engine and ECT) D


HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the brake actuator assembly (skid control ECU) and ECM or an internal malfunction of the combination meter assembly is suspected.




A

4.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

B

C

D

4.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
a.

Replace the brake actuator assembly (skid control ECU) with a new or a known good one.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Result Proceed to
The operation of the fuel economy meter returns to normal. A
The operation of the fuel economy meter does not return to normal. B



A

END

B

5.REPLACE ECM
5.REPLACE ECM
a.

Replace the ECM with a new or a known good one.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Result Proceed to
The operation of the fuel economy meter returns to normal. A
The operation of the fuel economy meter does not return to normal. B



A

END

B

REPLACE COMBINATION METER ASSEMBLY