Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074081 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines. Using this circuit, the radio and display receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E268499E54
0.833,0.802 1.333,0.969 0.5,0.167 10 false MACC 0.844,1.271 1.344,1.438 0.5,0.167 10 false MCO+ 0.875,1.75 1.375,1.917 0.5,0.167 10 false MCO- 0.865,2.698 1.281,2.865 0.417,0.167 10 false SNS2 0.167,3.156 0.646,3.385 0.479,0.229 10 false S7 0.167,3.323 2.573,3.74 2.406,0.417 10 false Roof Console Box Assembly (Telephone Microphone Assembly) 3.281,2.083 4.052,2.292 0.771,0.208 10 false (Shielded) 5.927,0.802 6.427,0.969 0.5,0.167 10 false MACC 5.927,1.271 6.344,1.438 0.417,0.167 10 false MIN+ 5.927,1.75 6.26,1.917 0.333,0.167 10 false MIN- 5.927,2.229 6.427,2.396 0.5,0.167 10 false SGND 5.927,2.698 6.344,2.865 0.417,0.167 10 false SNS2 5.438,3.156 6.031,3.469 0.594,0.313 10 false I155 5.438,3.323 7.135,3.74 1.698,0.417 10 false Radio and Display Receiver Assembly 1.333,0.698 1.583,0.875 0.25,0.177 10 false 14 1.333,1.167 1.615,1.344 0.281,0.177 10 false 13 1.333,1.646 1.615,1.823 0.281,0.177 10 false 12 1.333,2.594 1.5,2.76 0.167,0.167 10 false 15 5.74,0.698 5.906,0.865 0.167,0.167 10 false 4 5.74,1.167 5.906,1.333 0.167,0.167 10 false 5 5.74,2.594 5.906,2.76 0.167,0.167 10 false 6 5.667,1.646 5.917,1.813 0.25,0.167 10 false 19 5.667,2.125 5.917,2.292 0.25,0.167 10 false 18

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the I155 radio and display receiver assembly connector.


b.

Disconnect the S7 roof console box assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-6 (SNS2) - S7-15 (SNS2) Always Below 1 Ω
I155-4 (MACC) - S7-14 (MACC) Always Below 1 Ω
I155-5 (MIN+) - S7-13 (MCO+) Always Below 1 Ω
I155-19 (MIN-) - S7-12 (MCO-) Always Below 1 Ω
I155-6 (SNS2) - Body ground Always 10 kΩ or higher
I155-4 (MACC) - Body ground Always 10 kΩ or higher
I155-5 (MIN+) - Body ground Always 10 kΩ or higher
I155-19 (MIN-) - Body ground Always 10 kΩ or higher
I155-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the I155 radio and display receiver assembly connector.


b.

Reconnect the S7 roof console box assembly (telephone microphone assembly) connector.


c.
E289390C16
1.427,0.656 1.802,0.896 0.375,0.24 2.073,2 1.365,2.573 false 2.188,2 2.469,2.573 false 2.219,1.75 2.469,0.906 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.5,0.698 1.813,0.896 0.313,0.198 10 false I155 1.125,2.594 1.635,2.854 0.51,0.26 10 false MIN- 2.479,2.594 2.99,2.854 0.51,0.26 10 false SGND 2.469,0.698 2.979,0.958 0.51,0.26 10 false MACC
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I155-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-18 (SGND) - Body ground Always Below 1 Ω
I155-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the roof console box assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E187117C59
1.74,1.406 1.365,1.677 false 2.135,1.406 2.51,1.677 false 0.156,0.063 0.354,0.26 0.198,0.198 10 false *a 1.135,1.719 1.885,2.073 0.75,0.354 10 false SNS2 2.406,1.708 3.094,2.021 0.688,0.313 10 false MCO-
*a Component without harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
15 (SNS2) - 12 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
5.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the I155 radio and display receiver assembly connector.


b.

Reconnect the S7 roof console box assembly (telephone microphone assembly) connector.


c.

Turn the ignition switch to ACC.


d.
E187122C64
1.49,0.5 1.979,0.792 0.49,0.292 2.021,2.25 1.479,2.781 false 2.156,2.25 2.656,2.75 false 1.646,0.563 2.271,0.833 0.625,0.271 10 false S7 0.177,0.094 0.521,0.365 0.344,0.271 10 false *a 1.219,2.802 1.896,3.094 0.677,0.292 10 false MCO+ 2.573,2.771 3.271,3.135 0.698,0.365 10 false MCO-
*a Component with harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S7 roof console box assembly (telephone microphone assembly) connector.


e.

Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output. B




A

B

6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.

Result:
Result Proceed to
Malfunction does not recur (returns to normal). A
Malfunction recurs. B




A

END

B

REPLACE ROOF CONSOLE BOX ASSEMBLY