Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2015.04–2016.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Either condition is met:
·

"Clearance Warning (Clearance Sonar2)" is not displayed on the "CAN Bus Check" screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Clearance Warning ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Clearance warning ECU assembly branch line or connector

·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly ground circuit

·

Clearance warning ECU assembly



WIRING DIAGRAM

C241448E17
2.094,1.292 1.927,0.667 1.927,0.667 1.708,0.667 false 4.5,1.292 4.646,0.635 4.646,0.635 4.823,0.635 false 1.417,4.99 3.292,5.156 1.875,0.167 10 false : CAN Main Bus Line (CANH) 1.417,5.406 3.302,5.583 1.885,0.177 10 false : CAN Main Bus Line (CANL) 4.406,5 6.177,5.188 1.771,0.188 10 false : CAN Branch Line (CANH) 4.406,5.406 6.146,5.573 1.74,0.167 10 false : CAN Branch Line (CANL) 1.458,3.938 2.333,4.104 0.875,0.167 10 false Trouble Area 3.625,4.063 5.167,4.385 1.542,0.323 10 false Clearance Warning ECU Assembly 0.781,2.219 1.271,2.375 0.49,0.156 10 false 120 Ω 6.115,2.219 6.604,2.375 0.49,0.156 10 false 120 Ω 0.438,0.573 1.656,0.948 1.219,0.375 10 false CAN No. 1 Junction Connector 4.875,0.542 6.833,0.729 1.958,0.188 10 false CAN No. 2 Junction Connector 3.302,0.51 3.698,0.667 0.396,0.156 10 false DLC3 4.063,3.271 4.271,3.417 0.208,0.146 10 false R1 4.479,3.271 4.698,3.417 0.219,0.146 10 false R2 3.635,3.615 3.833,3.792 0.198,0.177 10 false IG 2.552,3.75 3.552,3.938 1,0.188 10 false ECU-IG1 NO. 2 4.833,3.604 4.99,3.792 0.156,0.188 10 false E 3.469,3.5 3.594,3.677 0.125,0.177 10 false 1 4.583,3.083 4.771,3.24 0.188,0.156 10 false 18 3.969,3.083 4.156,3.24 0.188,0.156 10 false 17 5.073,3.5 5.281,3.677 0.208,0.177 10 false 30 3.354,4.063 3.594,4.229 0.24,0.167 10 false I82 5.917,2.792 7.125,3.198 1.208,0.406 10 false Combination Meter Assembly 0.833,2.833 1.198,2.979 0.365,0.146 10 false ECM 0.125,0.052 1.427,0.344 1.302,0.292 12 false V Bus (for RHD): 5.688,2.792 6.042,2.979 0.354,0.188 10 false I18 0.531,2.833 1.063,2.99 0.531,0.156 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 14 seconds.

·

After the repair, perform the CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CLEARANCE WARNING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.


c.
C240532C01
1.219,0.573 1.708,0.865 0.49,0.292 2.656,1.906 2.656,0.792 2.656,0.792 2.458,0.792 false 2.792,1.896 2.792,0.781 2.792,0.781 2.99,0.781 false 0.198,0.156 0.375,0.333 0.177,0.177 10 *a 2.24,0.698 2.469,0.896 0.229,0.198 10 R1 3.031,0.698 3.26,0.896 0.229,0.198 10 R2 1.365,0.635 1.646,0.813 0.281,0.177 10 I82
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I82-17 (R1) - I82-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C240532C02
1.573,0.406 2.063,0.698 0.49,0.292 1.781,2.083 1.781,2.521 false 0.198,0.104 0.375,0.281 0.177,0.177 10 false *a 1.75,2.552 1.99,2.823 0.24,0.271 10 false E 1.719,0.469 2,0.646 0.281,0.177 10 false I82
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I82-30 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.
C240532C03
1.573,0.49 2.063,0.781 0.49,0.292 0.719,1.906 0.719,0.792 0.719,0.792 0.979,0.792 false 0.198,0.156 0.375,0.333 0.177,0.177 10 false *a 1.042,0.708 1.427,0.969 0.385,0.26 10 false IG 1.708,0.542 1.99,0.719 0.281,0.177 10 false I82
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I82-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)