Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2015.04
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074131 ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

The transponder key coil is built into the transponder key amplifier and receives a key code signal from the transponder chip in the key. This signal is amplified by the amplifier, then it is output to the transponder key ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2784 Antenna Coil Open / Short The antenna coil in the transponder key coil is open/shorted.
·

Wire harness or connector

·

Transponder key amplifier

·

Transponder key ECU assembly



WIRING DIAGRAM

B329324E42
5.552,2.542 6.01,2.74 0.458,0.198 10 false I19 5.542,2.698 6.906,3.219 1.365,0.521 10 false Transponder Key ECU Assembly 1.292,3.042 1.75,3.24 0.458,0.198 10 false I188 1.281,3.188 2.75,3.49 1.469,0.302 10 false Transponder Key Coil 2.792,0.76 3.552,1.052 0.76,0.292 10 false ANT1 2.781,1.948 3.542,2.24 0.76,0.292 10 false ANT2 5.677,0.896 6.438,1.188 0.76,0.292 10 false ANT1 5.677,2.052 6.438,2.344 0.76,0.292 10 false ANT2 5.51,0.802 5.75,1.042 0.24,0.24 10 false 4 5.427,1.958 5.667,2.198 0.24,0.24 10 false 15 3.25,0.75 3.49,0.99 0.24,0.24 10 false 1 3.229,1.948 3.469,2.188 0.24,0.24 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
DTC B2784 is output B



A

B

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connector is properly connected to the transponder key coil.


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
DTC B2784 is output B



A

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

B

6.CHECK TRANSPONDER KEY COIL (OUTPUT)
6.CHECK TRANSPONDER KEY COIL (OUTPUT)
a.

Using an oscilloscope, check the waveform.

B329326C21
3.417,0.073 3.74,0.292 0.323,0.219 3.938,1.271 3.792,1.271 3.792,1.271 3.792,0.802 true 3.188,1.26 3.354,1.26 3.354,1.26 3.354,0.802 true 2.938,0.073 3.25,0.271 0.313,0.198 10 false *a 1,1.448 1.313,1.646 0.313,0.198 10 false *b 1,3.542 1.313,3.74 0.313,0.198 10 false *c 6.542,2.479 7.083,2.781 0.542,0.302 10 false GND 6.552,4.552 7.094,4.854 0.542,0.302 10 false GND 4,1.188 4.542,1.49 0.542,0.302 10 false ANT1 2.823,1.177 3.365,1.479 0.542,0.302 10 false ANT2 3.448,0.094 3.906,0.292 0.458,0.198 10 false I188
*a Component with harness connected
(Transponder Key Coil)
*b Waveform 1
*c Waveform 2 - -


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
I188-1 (ANT1) - Body ground Within 3 seconds of inserting key into ignition key cylinder 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
I188-5 (ANT2) - Body ground Within 3 seconds of inserting key into ignition key cylinder 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY COIL)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY COIL)
a.

Disconnect the I19 transponder key ECU assembly connector.


b.

Disconnect the I188 transponder key coil connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I19-4 (ANT1) - I188-1 (ANT1) Always Below 1 Ω
I19-4 (ANT1) or I188-1 (ANT1) - Body ground Always 10 kΩ or higher
I19-15 (ANT2) - I188-5 (ANT2) Always Below 1 Ω
I19-15 (ANT2) or I188-5 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one.

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.


HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
DTC B2784 is output B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B