Home › Engine / Hybrid System › 2AR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014577 2AR-FE INTAKE / EXHAUST _0073950 EXHAUST MANIFOLD A

2AR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 25586 1.INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR

a.

Install the No. 1 manifold converter insulator with the 4 bolts.

Torque:
14 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 17168 2.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator with the 2 bolts.

Torque:
14 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 25051 3.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.

Set a new gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold converter sub-assembly with the 5 nuts.


c.

Temporarily install the No. 2 manifold stay and manifold stay with the 2 bolts and 2 nuts.


d.
A292055N01
1.417,1.677 1.615,1.823 0.198,0.146 10 1 0.698,0.042 0.854,0.24 0.156,0.198 10 2 2.698,0.094 2.854,0.292 0.156,0.198 10 3 0.313,1.656 0.469,1.854 0.156,0.198 10 4 3.083,1.667 3.24,1.865 0.156,0.198 10 5

Tighten the 5 nuts in the sequence shown in the illustration.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17139 5.INSTALL NO. 2 MANIFOLD STAY

a.

Install the No. 2 manifold stay with the bolt and nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17118 6.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the bolt and nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17410 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum 40.5 mm (1.60 in.)

HINT:

If the length is less than the minimum, replace the compression spring.



b.

Fully insert a new gasket to the exhaust manifold converter sub-assembly.


c.
A181728C35
1.667,0.146 1.823,0.146 1.823,0.146 1.833,1.125 false 2.042,2.302 1.188,2.615 1.188,2.615 0.99,2.615 false 2.521,1.385 2.833,1.563 2.833,1.563 2.833,1.802 false 1.448,0.083 1.635,0.271 0.188,0.188 10 false *1 0.76,2.531 0.927,2.719 0.167,0.188 10 false *2 2.792,1.865 3.031,2.073 0.24,0.208 10 false *3
*1 Exhaust Manifold Converter Sub-assembly
*2 Gasket
*3 Wooden Block


Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Install a new gasket to the front exhaust pipe assembly.


e.

Connect the front exhaust pipe assembly to the exhaust pipe support.


f.

Install the front exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


g.

Connect the heated oxygen sensor connector.


Hide 51441C 8.INSTALL ENGINE UNDER COVER RH

Hide 51442C 9.INSTALL ENGINE UNDER COVER LH

Hide 53851Z 10.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 53852K 11.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 13.INSPECT FOR EXHAUST GAS LEAK