Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074080 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the combination meter assembly.


for "Bluetooth":

Speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E309106E01
1,0.552 1.458,0.75 0.458,0.198 10 false SP1 1.375,0.542 1.833,0.74 0.458,0.198 10 false 2 5.24,0.333 5.531,0.531 0.292,0.198 10 false 8*7 5.625,0.656 6.083,0.854 0.458,0.198 10 false SI 5.625,2.573 6.083,2.771 0.458,0.198 10 false +S 5.25,2.458 5.708,2.656 0.458,0.198 10 false 3*8 5.25,2.802 5.708,3 0.458,0.198 10 false I18 1.708,2.479 2.167,2.677 0.458,0.198 10 false SPD 2.104,2.479 2.563,2.677 0.458,0.198 10 false 27 0.042,1.26 0.5,1.458 0.458,0.198 10 false A49 2.917,2.469 3.375,2.667 0.458,0.198 10 false 15 3.958,2.469 4.417,2.667 0.458,0.198 10 false 18 2.104,3.75 2.563,3.948 0.458,0.198 10 false 11 1.708,3.75 2.167,3.948 0.458,0.198 10 false SPD 0.052,2.74 0.51,2.938 0.458,0.198 10 false I78 0.354,4 0.813,4.198 0.458,0.198 10 false I69 1.688,5.01 2.146,5.208 0.458,0.198 10 false SPD 2.094,5 2.552,5.198 0.458,0.198 10 false 57 2.906,3.76 3.365,3.958 0.458,0.198 10 false 19 2.906,5.01 3.365,5.208 0.458,0.198 10 false 16 2.917,6.25 3.375,6.448 0.458,0.198 10 false 20 2.104,6.25 2.563,6.448 0.458,0.198 10 false 24 1.698,6.26 2.156,6.458 0.458,0.198 10 false SPD 1.115,5.438 1.573,5.635 0.458,0.198 10 false A25 1.51,5.438 1.969,5.635 0.458,0.198 10 false ECM 0.365,6.552 0.823,6.75 0.458,0.198 10 false I72 2.875,6.896 3.333,7.094 0.458,0.198 10 false I181 3.99,3.76 4.448,3.958 0.458,0.198 10 false 17 5.344,3.74 5.802,3.938 0.458,0.198 10 false 17 5.615,3.76 6.073,3.958 0.458,0.198 10 false SPD 5.625,5 6.083,5.198 0.458,0.198 10 false SPD 5.604,6.281 6.063,6.479 0.458,0.198 10 false SPD 5.333,5 5.792,5.198 0.458,0.198 10 false 17 5.302,6.25 5.76,6.448 0.458,0.198 10 false 17 5.24,4.021 5.698,4.219 0.458,0.198 10 false I150 4.625,5.292 5.083,5.49 0.458,0.198 10 false I155 5.063,6.594 5.521,6.792 0.458,0.198 10 false I67 0.052,1.417 3.583,1.625 3.531,0.208 10 false Brake Actuator Assembly (Skid Control ECU) 0.042,2.896 3.052,3.146 3.01,0.25 10 false Certification ECU (Smart Key ECU Assembly)*4 0.365,4.167 3.375,4.417 3.01,0.25 10 false Stereo Component Amplifier Assembly*5 0.344,6.729 3.354,6.979 3.01,0.25 10 false Windshield Wiper Relay Assembly*6 3.198,6.885 4.49,7.104 1.292,0.219 10 false Junction Connector 5.229,2.969 7.156,3.219 1.927,0.25 10 false Combination Meter Assembly 5.229,4.188 7.156,4.438 1.927,0.25 10 false Radio Receiver Assembly*1 4.604,5.438 7.156,5.688 2.552,0.25 10 false Radio and Display Receiver Assembly*2 5.052,6.76 7.156,7.01 2.104,0.25 10 false Navigation Receiver Assembly*3 0.198,7.51 7.156,7.75 6.958,0.24 10 false *1: for Radio Receiver Type 0.198,7.917 7.156,8.156 6.958,0.24 10 false *4: w/ Smart Entry and Start System 2.229,7.51 4.865,7.75 2.635,0.24 10 false *2: for Radio and Display Type 2.698,7.917 4.469,8.146 1.771,0.229 10 false *5: for 10 Speakers 4.417,7.51 7.052,7.75 2.635,0.24 10 false *3: for Navigation Receiver Type 4.25,7.917 6.885,8.156 2.635,0.24 10 false *6: w/ Auto Wiper System 5.25,0.531 5.688,0.771 0.438,0.24 10 false 4*8 5.25,2.26 5.521,2.438 0.271,0.177 10 false 9*7 0.208,8.292 2.75,8.542 2.542,0.25 10 false *7: w/o Multi-information Display 2.5,8.292 5.042,8.542 2.542,0.25 10 false *8: w/ Multi-information Display

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Check the output waveform.

E265532C01
1.781,0.302 2.156,0.563 0.375,0.26 1.49,1.979 1.771,1.302 false 1.885,0.354 2.344,0.552 0.458,0.198 10 l18 0.271,0.198 0.583,0.396 0.313,0.198 10 *a 6.083,1.458 6.542,1.656 0.458,0.198 10 GND 1.396,2.01 1.844,2.292 0.448,0.281 10 +S 4.615,1.625 5.073,1.823 0.458,0.198 10 (A)
*a Component with harness connected
(Combination Meter Assembly)
- -


i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I18-9 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-9 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the radio receiver assembly and combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-17 (SPD) - I18-9 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the radio receiver assembly connector and junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-17 (SPD) - I181-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)