Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0116  Engine Coolant Temperature Circuit Range / Performance  


DESCRIPTION

Refer to DTC P0115 (See page Engine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0115).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0116 Engine Coolant Temperature Circuit Range / Performance w/ tumble control valve:
Either of the following conditions is met (2 trip detection logic):
·

When engine is started cold and warmed up, the engine coolant temperature sensor value does not change.

·

After the warmed up engine is stopped and then next cold engine start is performed, the engine coolant temperature sensor value does not change.


w/o tumble control valve:
Engine coolant temperature between -40°C and 60°C (-40°F and 140°F) when engine started, and conditions (a) and (b) met (2 trip detection logic):

(a) Vehicle driven at varying speeds (accelerated and decelerated).

(b) Engine coolant temperature remains within 3°C (5.4°F) of initial engine coolant temperature.


·

Thermostat

·

Engine coolant temperature sensor


Comes on DTC stored

MONITOR DESCRIPTION

Engine Coolant Temperature Sensor Cold Start Monitor (w/ tumble control valve)

When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and this DTC is stored.


Engine Coolant Temperature Sensor Soak Monitor (w/ tumble control valve)

If the engine coolant temperature sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and this DTC is stored.


Engine Coolant Temperature Sensor High Side Stuck Monitor (w/o tumble control valve)

The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. If the sensor voltage output deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the engine coolant temperature sensor and stores the DTC.

Examples:

When starting the engine and the engine coolant temperature is between -40 and 60°C (-40 and 140°F):

If after driving for 250 seconds, the engine coolant temperature remains within 3°C (5.4°F) of the starting temperature, the DTC is stored (2 trip detection logic).



MONITOR STRATEGY

Required Sensors/Components Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

w/ Tumble Control Valve:
A198823E40
0.906,1.146 1.427,1.427 0.521,0.281 10 40 km/h 1.063,1.698 1.625,2.031 0.563,0.333 10 Idling 2.74,2.531 3.958,2.781 1.219,0.25 10 5 minutes or more 4.125,0.125 5.833,0.271 1.708,0.146 10 Total of 5 minutes or more 2.073,1.917 2.365,2.156 0.292,0.24 10 [A] 3.25,1.635 3.625,1.917 0.375,0.281 10 [B] 3.99,2.865 4.302,3.125 0.313,0.26 10 [C] 6.156,2.865 6.49,3.125 0.333,0.26 10 [E] 0.5,2 1.406,2.375 0.906,0.375 10 Ignition Switch ON 4.833,0.656 5.167,0.938 0.333,0.281 10 [D] 1.385,3.125 6.708,3.333 5.323,0.208 10 HINT: Start the engine when the engine coolant temperature is 60°C or less

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

4.

Check that the engine coolant temperature is 60°C (140°F) or less.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the GTS on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

HINT:

If the engine coolant temperature does not change by 5°C (9°F) or higher, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0116.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



14.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.


15.

Check the DTC judgment result again [E].

HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.




w/o Tumble Control Valve:
A254128E12
3.656,0.26 5.313,0.417 1.656,0.156 10 false Total of 5 minutes or more 1.052,1.76 1.406,1.958 0.354,0.198 10 false Idling 0.271,2.052 1.792,2.458 1.521,0.406 10 false Ignition Switch ON 2.135,1.885 2.333,2.052 0.198,0.167 10 false [A] 5.833,2.854 6.031,3.031 0.198,0.177 10 false [C] 3.313,0.646 3.521,0.813 0.208,0.167 10 false [B] 5.344,0.646 5.552,0.813 0.208,0.167 10 false [B] 4.823,0.646 5.031,0.813 0.208,0.167 10 false [B] 4.323,0.646 4.531,0.813 0.208,0.167 10 false [B] 3.813,0.646 4.021,0.813 0.208,0.167 10 false [B] 3.958,1.823 5.031,1.969 1.073,0.146 10 false 10 times or more 0.844,1.531 2.24,1.708 1.396,0.177 10 false 30 km/h 0.833,0.813 2.021,0.979 1.188,0.167 10 false 60 km/h 1.115,3.094 5.969,3.448 4.854,0.354 10 false HINT: Start the engine when the engine coolant temperature is 60°C or less

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

4.

Check that the engine coolant temperature is 60°C (140°F) or less.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the GTS on [A].

8.

Start the engine.

9.

Drive the vehicle at varying speeds (accelerated and decelerated more than 10 times) for 5 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the driving pattern can be resumed.


10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0116.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.





CAUTION / NOTICE / HINT

HINT:
·

If any of DTCs P0115, P0117 or P0118 are set simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.

·

When the DTC is output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0116 is output A
DTC P0116 and other DTCs are output B


HINT:

If any DTCs other than P0116 are output, troubleshoot those DTCs first.




A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT
a.

Inspect the thermostat (opening temperature).

Click hereEngine / Hybrid System>2AR-FE COOLING>THERMOSTAT>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG