Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P2111  Throttle Actuator Control System - Stuck Open  P2112  Throttle Actuator Control System - Stuck Closed  


DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle with motor body assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This Electronic Throttle Control System (ETCS) does not use a throttle cable.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2111 Throttle Actuator Control System - Stuck Open The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
·

Throttle actuator

·

Throttle with motor body assembly

·

Throttle valve

·

Wire harness or connector

·

ECM


Comes on DTC stored
P2112 Throttle Actuator Control System - Stuck Closed The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
·

Throttle actuator

·

Throttle with motor body assembly

·

Throttle valve

·

Wire harness or connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Throttle actuator (throttle with motor body assembly)
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

All
Throttle actuator On
Throttle actuator duty calculation Executing
Throttle position sensor fail Not detected
Throttle actuator current-cut operation Not executing
Throttle actuator power supply 4 V or higher
Throttle actuator fail Not detected

P2111: Throttle Actuator Stuck Open
All of the following conditions are met: -
Throttle actuator current 2 A or higher
Duty-cycle to close throttle 80% or higher

P2112: Throttle Actuator Stuck Closed
All of the following conditions are met: -
Throttle actuator current 2 A or higher
Duty-cycle to open throttle 80% or higher

TYPICAL MALFUNCTION THRESHOLDS

Throttle position sensor voltage No change

CONFIRMATION DRIVING PATTERN

A199314E27
0.104,0.052 1.615,0.229 1.51,0.177 10 Accelerator Pedal State 0.927,0.385 1.656,0.531 0.729,0.146 10 Depressed 0.938,0.875 1.583,1.031 0.646,0.156 10 Released 1.208,2.323 1.667,2.646 0.458,0.323 10 Idling 0.417,2.604 1.75,2.896 1.333,0.292 10 Ignition Switch ON 2.073,2.698 2.271,2.885 0.198,0.188 10 [A] 4.396,3.427 4.885,3.698 0.49,0.271 10 [B]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2111 or P2112.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle valve opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)].

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P2111 or P2112 is output A
DTC P2111 or P2112 and other DTCs are output B


HINT:

If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.



A

2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

B

2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for contamination between the throttle valve and housing. If necessary, clean the throttle with motor body assembly. Also check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.


HINT:

Perform "Inspection After Repair" after cleaning the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (THROTTLE POSITION)

NG

5.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
3.READ VALUE USING GTS (THROTTLE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

Powertrain > Engine and ECT > Data List
Tester Display
Throttle Position No.1
Throttle Position No.2
Throttle Position Command
50003 234 282,283,277

i.

Read the values displayed on the GTS while wiggling the ECM wire harness.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
Value in Data List changes when wire harness is wiggled, or DTC is output A
Other than above B



A

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY)

B

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY)
a.

As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


Result:
Proceed to
NEXT



NEXT

END

5.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Replace the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not output A
DTC P2111 or P2112 is output B



A

END

B