Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0265  Lost Communication with Parking Assist Monitor Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0265 Lost Communication with Parking Assist Monitor Module No communication from the rear television camera assembly continues.
·

Rear television camera assembly branch line or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly


Network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.

HINT:

This diagnosis procedure is for when DTC U0265 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C320999E03
1.698,2.146 1.698,1.063 1.698,1.063 1.906,1.063 false 2.729,2.146 2.729,1.417 2.729,1.417 2.938,1.417 false 3.844,2.135 3.844,1.854 3.844,1.854 4.052,1.854 false 0.125,0.125 6.135,0.729 6.01,0.604 12 false Sub Bus 2 (w/ Parking Assist Monitor System without Pre-crash Safety System and Lane Departure Alert System) 1.198,6.115 3.104,6.323 1.906,0.208 10 false : CAN Main Bus Line (CANH) 1.198,6.458 3.104,6.667 1.906,0.208 10 false : CAN Main Bus Line (CANL) 4.333,6.115 6.24,6.323 1.906,0.208 10 false : CAN Branch Line (CANH) 4.333,6.438 6.24,6.646 1.906,0.208 10 false : CAN Branch Line (CANL) 0.146,3.688 1.792,3.979 1.646,0.292 10 false Network Gateway ECU 0.552,4.948 1.458,5.406 0.906,0.458 10 false Trouble Area 2.052,4.49 2.698,5.125 0.646,0.635 10 false Navigation Receiver Assembly 5.219,4.448 5.875,5.125 0.656,0.677 10 false Navigation Receiver Assembly 3.135,5.375 5.375,5.677 2.24,0.302 10 false Rear Television Camera Assembly 2.865,5.375 3.198,5.604 0.333,0.229 10 false T22 3.302,4.719 3.635,4.948 0.333,0.229 10 false CB+ 3.135,4.594 3.469,4.823 0.333,0.229 10 false 6 3.573,4.542 4.052,4.771 0.479,0.229 10 false CANH 4,4.542 4.479,4.771 0.479,0.229 10 false CANL 4.271,4.698 4.75,4.927 0.479,0.229 10 false CGND 4.74,4.583 5.073,4.813 0.333,0.229 10 false 5 3.646,4.333 3.979,4.563 0.333,0.229 10 false 4 4.25,4.333 4.583,4.563 0.333,0.229 10 false 1 0.729,3.083 1.156,3.406 0.427,0.323 10 false 120 Ω 6.198,3.073 6.625,3.396 0.427,0.323 10 false 120 Ω 2,0.979 4.365,1.281 2.365,0.302 10 false CAN No. 9 Junction Connector 3.021,1.333 5.385,1.635 2.365,0.302 10 false CAN No. 5 Junction Connector 4.146,1.781 6.51,2.083 2.365,0.302 10 false CAN No. 6 Junction Connector 5.781,3.698 7,4.146 1.219,0.448 10 false CAN No. 7 Junction Connector

C318604E04
4.74,2.146 4.74,1.844 4.74,1.844 4.979,1.844 false 3.448,2.146 3.448,1.594 3.448,1.594 3.688,1.594 false 1.677,2.135 1.677,1.01 1.677,1.01 1.917,1.01 false 2.427,2.146 2.427,1.313 2.427,1.313 2.667,1.313 false 0.177,0.073 5.802,0.625 5.625,0.552 12 false Sub Bus 2 (w/ Parking Assist Monitor System, Blind Spot Monitor System and Lane Departure Alert System): 0.125,3.698 1.781,4.094 1.656,0.396 10 false Network Gateway ECU 1.198,6.115 3.042,6.406 1.844,0.292 10 false : CAN Main Bus Line (CANH) 2.063,4.479 2.708,5.26 0.646,0.781 10 false Navigation Receiver Assembly 5.219,4.479 5.865,5.083 0.646,0.604 10 false Navigation Receiver Assembly 3.302,4.719 3.74,4.969 0.438,0.25 10 false CB+ 3.604,4.542 4.031,4.813 0.427,0.271 10 false CANH 4.021,4.531 4.448,4.802 0.427,0.271 10 false CANL 4.25,4.698 4.677,4.969 0.427,0.271 10 false CGND 3.156,4.604 3.385,4.885 0.229,0.281 10 false 6 3.656,4.323 3.844,4.552 0.188,0.229 10 false 4 4.24,4.292 4.427,4.521 0.188,0.229 10 false 1 4.75,4.573 4.938,4.802 0.188,0.229 10 false 5 1.177,6.448 3.021,6.74 1.844,0.292 10 false : CAN Main Bus Line (CANL) 4.313,6.125 6.156,6.417 1.844,0.292 10 false : CAN Branch Line (CANH) 4.313,6.448 6.156,6.74 1.844,0.292 10 false : CAN Branch Line (CANL) 3.031,5.385 5.26,5.677 2.229,0.292 10 false Rear Television Camera Assembly 2.75,5.385 3.031,5.667 0.281,0.281 10 false T22 2.01,0.927 4.208,1.281 2.198,0.354 10 false CAN No. 8 Junction Connector 2.771,1.229 4.969,1.583 2.198,0.354 10 false CAN No. 9 Junction Connector 3.823,1.51 6.021,1.865 2.198,0.354 10 false CAN No. 5 Junction Connector 5.052,1.781 6.979,2.146 1.927,0.365 10 false CAN No. 6 Junction Connector 0.729,3.073 1.24,3.333 0.51,0.26 10 false 120 Ω 6.198,3.063 6.708,3.323 0.51,0.26 10 false 120 Ω 0.458,4.885 1.313,5.438 0.854,0.552 10 false Trouble Area 5.792,3.688 7.031,4.156 1.24,0.469 10 false CAN No. 7 Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 22 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150
HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) A
DTC U1002 is output from the network gateway ECU (GTS display: Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS 2 LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 2 LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the T22 rear television camera assembly connector.


c.
C294680C31
1.573,0.188 1.958,0.479 0.385,0.292 0.979,1.958 1.146,1.958 1.146,1.958 1.563,1.417 true 0.99,0.563 1.135,0.563 1.135,0.563 1.552,1.156 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.646,0.229 2.104,0.427 0.458,0.198 10 false T22 0.583,0.469 1.198,0.667 0.615,0.198 10 false CANL 0.563,1.865 1.177,2.063 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T22-4 (CANH) - T22-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C294680C32
1.573,0.188 1.958,0.479 0.385,0.292 1.198,1.958 1.365,1.958 1.365,1.958 1.781,1.417 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.656,0.229 2.115,0.427 0.458,0.198 10 false T22 0.76,1.865 1.375,2.063 0.615,0.198 10 false CGND
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T22-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C294680C33
1.573,0.188 1.958,0.479 0.385,0.292 1.385,1.958 1.552,1.958 1.552,1.958 1.969,1.417 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false T22 1.052,1.865 1.667,2.063 0.615,0.198 10 false CB+
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T22-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Result
OK
NG



OK

REPLACE REAR TELEVISION CAMERA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)