The network gateway ECU will store this DTC when no signals are received from the ECUs that have been memorized as those that are connected to sub bus 2.
When the network gateway ECU receives a response signal from the ECUs connected to sub bus 2, the network gateway ECU recognizes and memorizes that the ECU is connected to sub bus 2. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to sub bus 2 when communicating with those ECUs. If the network gateway ECU does not receive response signals from the ECUs that have been memorized as those connected to sub bus 2, the network gateway ECU determines that a malfunction exists.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| U1002 | Lost Communication with Gateway Module (Network Gateway ECU) | The network gateway ECU does not receive signals from all ECUs that have been memorized as those connected to sub bus 2. | ·
Open or short in sub bus 2 main lines or connector ·
Short in sub bus 2 branch lines or connector ·
Network gateway ECU (w/ Parking Assist Monitor System) ·
Blind spot monitor sensor RH (w/ Blind Spot Monitor System) ·
Rear television camera assembly (w/ Parking Assist Monitor System) ·
Driving support ECU assembly (w/ Pre-crash Safety System) ·
Lane departure warning camera (w/ Lane Departure Alert System) ·
Open or short in CAN No. 5 junction connector (w/ Parking Assist Monitor System) ·
Open or short in CAN No. 6 junction connector (w/ Parking Assist Monitor System) ·
Open or short in CAN No. 7 junction connector (w/ Parking Assist Monitor System) ·
Open or short in CAN No. 8 junction connector (w/ Lane Departure Alert System) ·
Open or short in CAN No. 9 junction connector (w/ Parking Assist Monitor System) |
The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2. |
This diagnosis procedure is for when DTC U1002 is output by the network gateway ECU (GTS display: Gateway).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 52 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/ Parking Assist Monitor System without Pre-crash Safety System, Lane Departure Alert System and Blind Spot Monitor System | A |
| w/ Parking Assist Monitor System and Blind Spot Monitor System without Pre-crash Safety System and Lane Departure Alert System | B |
| w/ Parking Assist Monitor System, Blind Spot Monitor System and Lane Departure Alert System | C |
A
B
C
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected
(Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in main bus lines | |||
| I160-13 (CA2H) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I160-12 (CA2L) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I160-13 (CA2H) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I160-12 (CA2L) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN main bus lines) | B |
| NG (Short circuit between bus lines) | C |
·
NG (Ground short) ·
NG (+B short) |
D |
A
B
C
D
Disconnect the T22 rear television camera assembly connector.
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T22-4 (CANH) - T22-1 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the T22 rear television camera assembly connector.
Reconnect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / IPA/Parking Assist Monitor / Trouble Codes.
| Result | Proceed to |
|---|---|
| DTC C1621 is not output from the rear television camera assembly (GTS display: IPA/Parking Assist Monitor) | A |
| DTC C1621 is output from the rear television camera assembly (GTS display: IPA/Parking Assist Monitor) | B |
A
B
Enter the following menus: Body Electrical / Gateway / Trouble Codes.
| Result | Proceed to |
|---|---|
| DTC U1002 is output from the network gateway ECU (GTS display: Gateway) | A |
| DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Replace the network gateway ECU.
Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU>REMOVAL
| Result |
|---|
| NEXT |
NEXT
Reconnect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Gateway / Trouble Codes.
| Result | Proceed to |
|---|---|
| DTC U1002 is output from the network gateway ECU (GTS display: Gateway) | A |
| DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) | B |
A
B
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I160 network gateway ECU connector.
Disconnect the I178 and I179 CAN No. 9 junction connectors.
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
| *b | to Network Gateway ECU |
| *c | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| I178-1 (CANH) - I178-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Network gateway ECU |
| I179-1 (CANH) - I179-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus lines) | B |
| NG (to CAN No. 5 junction connector main bus lines) | C |
A
B
C
Reconnect the I178 and I179 CAN No. 9 junction connectors.
Disconnect the O31 CAN No. 5 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
| *c | to CAN No. 9 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| O31-8 (CANH) - O31-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 6 junction connector |
| O31-11 (CANH) - O31-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 9 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus lines) | B |
| NG (to CAN No. 6 junction connector main bus lines) | C |
A
B
C
Reconnect the O31 CAN No. 5 junction connector.
Disconnect the T17 CAN No. 6 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
| *b | to CAN No. 7 Junction Connector |
| *c | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| T17-1 (CANH) - T17-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 7 junction connector |
| T17-3 (CANH) - T17-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus lines) | B |
| NG (to CAN No. 7 junction connector main bus lines) | C |
A
B
C
Reconnect the T17 CAN No. 6 junction connector.
Disconnect the T18 CAN No. 7 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 7 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T18-3 (CANH) - T18-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I160 network gateway ECU connector.
Disconnect the I178 and I179 CAN No. 9 junction connectors.
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
| *b | to Network Gateway ECU |
| *c | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| I178-1 (CANH) - I178-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Network gateway ECU |
| I179-1 (CANH) - I179-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus lines) | B |
| NG (to CAN No. 5 junction connector main bus lines) | C |
A
B
C
Reconnect the I178 and I179 CAN No. 9 junction connectors.
Disconnect the O31 CAN No. 5 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
| *c | to CAN No. 9 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| O31-8 (CANH) - O31-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 6 junction connector |
| O31-11 (CANH) - O31-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 9 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus lines) | B |
| NG (to CAN No. 6 junction connector main bus lines) | C |
A
B
C
Reconnect the O31 CAN No. 5 junction connector.
Disconnect the T17 CAN No. 6 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
| *b | to CAN No. 7 Junction Connector |
| *c | to Rear Television Camera Assembly |
| *d | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| T17-1 (CANH) - T17-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 7 junction connector |
| T17-2 (CANH) - T17-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Rear television camera assembly |
| T17-3 (CANH) - T17-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus lines) | B |
| NG (to CAN No. 7 junction connector main bus lines) | C |
| NG (to rear television camera assembly branch lines) | D |
A
B
C
D
Reconnect the T17 CAN No. 6 junction connector.
Disconnect the T18 CAN No. 7 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 7 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T18-3 (CANH) - T18-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the I178 and I179 CAN No. 9 junction connectors.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
*b | to Network Gateway ECU |
| *c | to CAN No. 5 Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| I178-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Network gateway ECU |
| I178-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| I179-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 5 junction connector |
| I179-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| I178-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Network gateway ECU |
| I178-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| I179-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 5 junction connector |
| I179-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus line) | B |
| NG (to CAN No. 5 junction connector main bus line) | C |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| I160-13 (CA2H) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I160-12 (CA2L) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I160-13 (CA2H) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I160-12 (CA2L) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result |
|---|
| OK |
| NG |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
OK
NG
Disconnect the O31 CAN No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
*b | to CAN No. 6 Junction Connector |
| *c | to CAN No. 9 Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| O31-8 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 6 junction connector |
| O31-19 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| O31-11 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 9 junction connector |
| O31-22 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| O31-8 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 6 junction connector |
| O31-19 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| O31-11 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 9 junction connector |
| O31-22 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus line) | B |
| NG (to CAN No. 6 junction connector main bus line) | C |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
Disconnect the T17 CAN No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
*b | to CAN No. 7 Junction Connector |
| *c | to Rear Television Camera Assembly | *d | to CAN No. 5 Junction Connector |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| T17-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 7 junction connector |
| T17-12 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-2 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Rear television camera assembly |
| T17-13 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-3 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 5 junction connector |
| T17-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 7 junction connector |
| T17-12 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| T17-2 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Rear television camera assembly |
| T17-13 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| T17-3 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 5 junction connector |
| T17-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus line) | B |
| NG (to CAN No. 7 junction connector main bus line) | C |
| NG (to rear television camera assembly branch line) | D |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
D
Disconnect the T18 CAN No. 7 junction connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 7 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| T18-3 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| T18-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| T18-3 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| T18-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected
(Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in main bus lines | |||
| I160-13 (CA2H) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I160-12 (CA2L) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I160-13 (CA2H) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I160-12 (CA2L) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN main bus lines) | B |
| NG (Short circuit between bus lines) | C |
·
NG (Ground short) ·
NG (+B short) |
D |
A
B
C
D
Reconnect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON and recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC U1002 is output from the network gateway ECU (GTS display: Gateway) | A |
| DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I160 network gateway ECU connector.
Disconnect the I178 and I179 CAN No. 9 junction connectors.
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
| *b | to Network Gateway ECU |
| *c | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| I178-1 (CANH) - I178-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Network gateway ECU |
| I179-1 (CANH) - I179-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus lines) | B |
| NG (to CAN No. 5 junction connector main bus lines) | C |
A
B
C
Reconnect the I178 and I179 CAN No. 9 junction connectors.
Disconnect the O31 CAN No. 5 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
| *c | to CAN No. 9 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| O31-8 (CANH) - O31-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 6 junction connector |
| O31-11 (CANH) - O31-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 9 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus lines) | B |
| NG (to CAN No. 6 junction connector main bus lines) | C |
A
B
C
Reconnect the O31 CAN No. 5 junction connector.
Disconnect the T17 CAN No. 6 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
| *b | to CAN No. 7 Junction Connector |
| *c | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| T17-1 (CANH) - T17-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 7 junction connector |
| T17-3 (CANH) - T17-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus lines) | B |
| NG (to CAN No. 7 junction connector main bus lines) | C |
A
B
C
Reconnect the T17 CAN No. 6 junction connector.
Disconnect the T18 CAN No. 7 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 7 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T18-3 (CANH) - T18-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I160 network gateway ECU connector.
Disconnect the I178 and I179 CAN No. 9 junction connectors.
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
| *b | to Network Gateway ECU |
| *c | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| I178-1 (CANH) - I178-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Network gateway ECU |
| I179-1 (CANH) - I179-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus lines) | B |
| NG (to CAN No. 5 junction connector main bus lines) | C |
A
B
C
Reconnect the I178 and I179 CAN No. 9 junction connectors.
Disconnect the O31 CAN No. 5 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
| *c | to Blind Spot Monitor Sensor RH |
| *d | to CAN No. 9 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| O31-8 (CANH) - O31-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 6 junction connector |
| O31-9 (CANH) - O31-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Blind spot monitor sensor RH |
| O31-11 (CANH) - O31-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 9 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus lines) | B |
| NG (to CAN No. 6 junction connector main bus lines) | C |
| NG (to blind spot monitor sensor RH branch lines) | D |
A
B
C
D
Reconnect the O31 CAN No. 5 junction connector.
Disconnect the T17 CAN No. 6 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
| *b | to CAN No. 7 Junction Connector |
| *c | to Rear Television Camera Assembly |
| *d | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| T17-1 (CANH) - T17-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 7 junction connector |
| T17-2 (CANH) - T17-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Rear television camera assembly |
| T17-3 (CANH) - T17-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus lines) | B |
| NG (to CAN No. 7 junction connector main bus lines) | C |
| NG (to rear television camera assembly branch lines) | D |
A
B
C
D
Reconnect the T17 CAN No. 6 junction connector.
Disconnect the T18 CAN No. 7 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 7 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T18-3 (CANH) - T18-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the I178 and I179 CAN No. 9 junction connectors.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
*b | to Network Gateway ECU |
| *c | to CAN No. 5 Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| I178-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Network gateway ECU |
| I178-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| I179-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 5 junction connector |
| I179-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| I178-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Network gateway ECU |
| I178-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| I179-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 5 junction connector |
| I179-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus line) | B |
| NG (to CAN No. 5 junction connector main bus line) | C |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| I160-13 (CA2H) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I160-12 (CA2L) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I160-13 (CA2H) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I160-12 (CA2L) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result |
|---|
| OK |
| NG |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
OK
NG
Disconnect the O31 CAN No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
*b | to CAN No. 6 Junction Connector |
| *c | to Blind Spot Monitor Sensor RH | *d | to CAN No. 9 Junction Connector |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| O31-8 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 6 junction connector |
| O31-19 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| O31-9 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Blind spot monitor sensor RH |
| O31-20 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| O31-11 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 9 junction connector |
| O31-22 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| O31-8 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 6 junction connector |
| O31-19 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| O31-9 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Blind spot monitor sensor RH |
| O31-20 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| O31-11 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 9 junction connector |
| O31-22 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus line) | B |
| NG (to CAN No. 6 junction connector main bus line) | C |
| NG (to blind spot monitor sensor RH branch line) | D |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
D
Disconnect the T17 CAN No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
*b | to CAN No. 7 Junction Connector |
| *c | to Rear Television Camera Assembly | *d | to CAN No. 5 Junction Connector |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| T17-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 7 junction connector |
| T17-12 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-2 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Rear television camera assembly |
| T17-13 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-3 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 5 junction connector |
| T17-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 7 junction connector |
| T17-12 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| T17-2 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Rear television camera assembly |
| T17-13 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| T17-3 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 5 junction connector |
| T17-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus line) | B |
| NG (to CAN No. 7 junction connector main bus line) | C |
| NG (to rear television camera assembly branch line) | D |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
D
Disconnect the T18 CAN No. 7 junction connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 7 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| T18-3 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| T18-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| T18-3 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| T18-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected
(Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in main bus lines | |||
| I160-13 (CA2H) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I160-12 (CA2L) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I160-13 (CA2H) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I160-12 (CA2L) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN main bus lines) | B |
| NG (Short circuit between bus lines) | C |
·
NG (Ground short) ·
NG (+B short) |
D |
A
B
C
D
Reconnect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON and recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC U1002 is output from the network gateway ECU (GTS display: Gateway) | A |
| DTC U1002 is not output from the network gateway ECU (GTS display: Gateway) | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I160 network gateway ECU connector.
Disconnect the I179 and I193 CAN No. 9 junction connectors.
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
| *b | to CAN No. 5 Junction Connector |
| *c | to CAN No. 8 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| I179-1 (CANH) - I179-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| I193-1 (CANH) - I193-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 8 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 8 junction connector main bus lines) | B |
| NG (to CAN No. 5 junction connector main bus lines) | C |
A
B
C
Reconnect the I179 and I193 CAN No. 9 junction connectors.
Disconnect the S15 CAN No. 8 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 8 Junction Connector) |
| *b | to CAN No. 9 Junction Connector |
| *c | to Network Gateway ECU |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| S15-2 (CANH) - S15-8 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 9 junction connector |
| S15-3 (CANH) - S15-9 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Network gateway ECU |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus lines) | B |
| NG (to CAN No. 9 junction connector main bus lines) | C |
A
B
C
Reconnect the I179 and I193 CAN No. 9 junction connectors.
Disconnect the O31 CAN No. 5 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
| *c | to CAN No. 9 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| O31-8 (CANH) - O31-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 6 junction connector |
| O31-11 (CANH) - O31-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 9 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus lines) | B |
| NG (to CAN No. 6 junction connector main bus lines) | C |
A
B
C
Reconnect the O31 CAN No. 5 junction connector.
Disconnect the T17 CAN No. 6 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
| *b | to CAN No. 7 Junction Connector |
| *c | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| T17-1 (CANH) - T17-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 7 junction connector |
| T17-3 (CANH) - T17-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus lines) | B |
| NG (to CAN No. 7 junction connector main bus lines) | C |
A
B
C
Reconnect the T17 CAN No. 6 junction connector.
Disconnect the T18 CAN No. 7 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 7 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T18-3 (CANH) - T18-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the I160 network gateway ECU connector.
Disconnect the I179, I192 and I193 CAN No. 9 junction connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
*b | to CAN No. 5 Junction Connector |
| *c | to Driving Support ECU Assembly
(w/ Pre-crash Safety System) |
*d | to CAN No. 8 Junction Connector |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| I179-1 (CANH) - I179-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| I192-1 (CANH) - I192-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Driving support ECU assembly* |
| I193-1 (CANH) - I193-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 8 junction connector |
*: w/ Pre-crash Safety System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 8 junction connector main bus lines) | B |
| NG (to CAN No. 5 junction connector main bus lines) | C |
| NG (to driving support ECU assembly branch lines) | D |
A
B
C
D
Reconnect the I179, I192 and I193 CAN No. 9 junction connectors.
Disconnect the S15 CAN No. 8 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 8 Junction Connector) |
| *b | to Lane Departure Warning Camera |
| *c | to CAN No. 9 Junction Connector |
| *d | to Network Gateway ECU |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| S15-1 (CANH) - S15-7 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Lane departure warning camera |
| S15-2 (CANH) - S15-8 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 9 junction connector |
| S15-3 (CANH) - S15-9 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Network gateway ECU |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus lines) | B |
| NG (to CAN No. 9 junction connector main bus lines) | C |
| NG (to lane departure warning camera branch lines) | D |
A
B
C
D
Reconnect the I179, I192 and I193 CAN No. 9 junction connectors.
Disconnect the O31 CAN No. 5 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
| *c | to Blind Spot Monitor Sensor RH |
| *d | to CAN No. 9 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| O31-8 (CANH) - O31-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 6 junction connector |
| O31-9 (CANH) - O31-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Blind spot monitor sensor RH |
| O31-11 (CANH) - O31-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 9 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus lines) | B |
| NG (to CAN No. 6 junction connector main bus lines) | C |
| NG (to blind spot monitor sensor RH branch lines) | D |
A
B
C
D
Reconnect the O31 CAN No. 5 junction connector.
Disconnect the T17 CAN No. 6 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
| *b | to CAN No. 7 Junction Connector |
| *c | to Rear Television Camera Assembly |
| *d | to CAN No. 5 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| T17-1 (CANH) - T17-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 7 junction connector |
| T17-2 (CANH) - T17-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Rear television camera assembly |
| T17-3 (CANH) - T17-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 5 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus lines) | B |
| NG (to CAN No. 7 junction connector main bus lines) | C |
| NG (to rear television camera assembly branch lines) | D |
A
B
C
D
Reconnect the T17 CAN No. 6 junction connector.
Disconnect the T18 CAN No. 7 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 7 Junction Connector) |
| *b | to CAN No. 6 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T18-3 (CANH) - T18-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short-circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *a | Component with harness connected
(Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I160-13 (CA2H) - I160-12 (CA2L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, repair or replace the short-circuited branch line or connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the I179, I192 and I193 CAN No. 9 junction connectors.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Rear view of wire harness connector
(to CAN No. 9 Junction Connector) |
*b | to CAN No. 5 Junction Connector |
| *c | to Driving Support ECU Assembly
(w/ Pre-crash Safety System) |
*d | to CAN No. 8 Junction Connector |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| I179-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 5 junction connector |
| I179-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| I192-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Driving support ECU assembly* |
| I192-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| I193-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 8 junction connector |
| I193-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| I179-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 5 junction connector |
| I179-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| I192-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Driving support ECU assembly* |
| I192-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| I193-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 8 junction connector |
| I193-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
*: w/ Pre-crash Safety System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 8 junction connector main bus line) | B |
| NG (to CAN No. 5 junction connector main bus line) | C |
| NG (to driving support ECU assembly branch line) | D |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
D
Disconnect the S15 CAN No. 8 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to CAN No. 8 Junction Connector) |
*b | to Lane Departure Warning Camera |
| *c | to CAN No. 9 Junction Connector | *d | to Network Gateway ECU |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| S15-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Lane departure warning camera |
| S15-7 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| S15-2 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 9 junction connector |
| S15-8 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| S15-3 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Network gateway ECU |
| S15-9 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| S15-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Lane departure warning camera |
| S15-7 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| S15-2 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 9 junction connector |
| S15-8 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| S15-3 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Network gateway ECU |
| S15-9 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to network gateway ECU main bus line) | B |
| NG (to CAN No. 9 junction connector main bus line) | C |
| NG (to lane departure warning camera branch line) | D |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
D
Disconnect the I160 network gateway ECU connector.
| *a | Front view of wire harness connector
(to Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| I160-13 (CA2H) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I160-12 (CA2L) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I160-13 (CA2H) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I160-12 (CA2L) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result |
|---|
| OK |
| NG |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
OK
NG
Disconnect the O31 CAN No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to CAN No. 5 Junction Connector) |
*b | to CAN No. 6 Junction Connector |
| *c | to Blind Spot Monitor Sensor RH | *d | to CAN No. 9 Junction Connector |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| O31-8 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 6 junction connector |
| O31-19 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| O31-9 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Blind spot monitor sensor RH |
| O31-20 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| O31-11 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 9 junction connector |
| O31-22 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| O31-8 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 6 junction connector |
| O31-19 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| O31-9 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Blind spot monitor sensor RH |
| O31-20 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| O31-11 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 9 junction connector |
| O31-22 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 9 junction connector main bus line) | B |
| NG (to CAN No. 6 junction connector main bus line) | C |
| NG (to blind spot monitor sensor RH branch line) | D |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
D
Disconnect the T17 CAN No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to CAN No. 6 Junction Connector) |
*b | to CAN No. 7 Junction Connector |
| *c | to Rear Television Camera Assembly | *d | to CAN No. 5 Junction Connector |
| Tester Connection | Condition | Specified Condition | Result | Connected to |
|---|---|---|---|---|
| T17-1 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 7 junction connector |
| T17-12 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-2 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | Rear television camera assembly |
| T17-13 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-3 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short | CAN No. 5 junction connector |
| T17-14 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short | |
| T17-1 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 7 junction connector |
| T17-12 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| T17-2 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | Rear television camera assembly |
| T17-13 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short | |
| T17-3 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short | CAN No. 5 junction connector |
| T17-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to CAN No. 5 junction connector main bus line) | B |
| NG (to CAN No. 7 junction connector main bus line) | C |
| NG (to rear television camera assembly branch line) | D |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
A
B
C
D
Disconnect the T18 CAN No. 7 junction connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 7 Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| T18-3 (CANH) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| T18-2 (CANL) - I39-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| T18-3 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| T18-2 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to B+ or shorted to GND is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *a | Component with harness connected
(Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| I160-13 (CA2H) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I160-12 (CA2L) - I160-4 (GND) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| I160-13 (CA2H) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I160-12 (CA2L) - I160-2 (BATT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result |
|---|
| OK |
| NG |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 2 inspection.
If the resistance becomes normal when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
OK
NG