Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM19V0EQ _53 Suspension _052591 TIRE PRESSURE MONITORING _0265587 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2179/79  Tire Pressure Monitor ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2179/79 Tire Pressure Monitor ECU Communication Stop Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
·

Main body ECU (Multiplex network body ECU)

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C257851E43
2.177,0.656 2.573,0.875 0.396,0.219 10 false PRG 2.583,0.521 2.875,0.781 0.292,0.26 10 false 4 4.469,0.521 4.635,0.688 0.167,0.167 10 false 5 4.365,1.365 7.021,1.542 2.656,0.177 10 false Tire Pressure Warning ECU and Receiver 0.26,1.198 0.542,1.365 0.281,0.167 10 false I13 0.26,1.385 3.292,1.719 3.031,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 4.354,1.167 5.813,1.396 1.458,0.229 10 false N44 4.656,0.656 5.573,0.854 0.917,0.198 10 false PRG2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the N44 tire pressure warning ECU and receiver connector.


b.

Disconnect the I13 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N44-5 (PRG2) - I13-4 (PRG) Always Below 1 Ω
N44-5 (PRG2) or I13-4 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Clear DTCs
50002 203

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Trouble Codes
50001 203
OK:

DTC C2179/79 is not output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)