Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM19V0EQ _53 Suspension _052591 TIRE PRESSURE MONITORING _0265587 TIRE PRESSURE WARNING SYSTEM Y

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the tire pressure warning system.

·

Make sure that the wireless door lock control system has exited diagnostic mode before performing the following procedure.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Interview the customer to confirm the problem.

HINT:

It is important to collect as much specific information as possible from the customer to allow for a quick repair.



Result:
Proceed to
NEXT



NEXT

3.ADJUST TIRE PRESSURE*
3.ADJUST TIRE PRESSURE*
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


e.

Set the all tire pressure to the specified value.

NOTICE:

Refer to the link as the procedure for adjusting the tire pressures differs depending on the temperature of the tires.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION



f.

Display "ID Tire Inflation Pressure" in the Data List and check that the tire pressure values match the adjusted pressure amount.

HINT:

It may take a few minutes until the values are displayed.



g.

Perform initialization.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION

HINT:
·

The warning threshold value changes depending on the driving conditions during initialization. As a result, the tire pressure warning light may not turn off even if the tire pressure is adjusted to the specified pressure.

·

The tire pressure warning system illuminates the tire pressure warning light to warn the driver when any of the following conditions are met:

·

Due to the operation of the tire pressure warning reset switch, the tire pressure drops to approximately 80% or less of the tire pressure set during system initialization.

·

The tire pressure drastically decreases (approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more within several minutes) to approximately 80% or less of the tire pressure* when the tires are warmed.

*: If initialization is performed and the vehicle is driven for a certain period of time, the tire pressure set during system initialization is adjusted and set to the tire pressure when the tires are warmed from the driving conditions.

NOTICE:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.






Result:
Result Proceed to
Tire pressure warning light remains on A
Tire pressure warning light goes off B



A

4.CHECK ECU CONNECTED TO CAN BUS*

B

END

4.CHECK ECU CONNECTED TO CAN BUS*
a.

Check the ECUs connected to the CAN bus.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
No malfunction appears A
Malfunction appears B



A

5.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)*

B

5.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)*

Result:
Result Proceed to
CAN system DTCs are not output A
CAN system DTCs are output B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

7.DTC CHART

B

8.PROBLEM SYMPTOMS TABLE
7.DTC CHART

Result:
Proceed to
NEXT



NEXT

10.REPAIR OR REPLACE
8.PROBLEM SYMPTOMS TABLE

Result:
Proceed to
NEXT



NEXT

9.CIRCUIT INSPECTION*
9.CIRCUIT INSPECTION*

Result:
Proceed to
NEXT



NEXT

10.REPAIR OR REPLACE
10.REPAIR OR REPLACE
a.

Repair or replace parts based on the diagnosis result.


Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST*
11.CONFIRMATION TEST*
a.

Check the Data List to confirm that the tire inflation pressure has been received.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST



c.

Confirm that the initialization has been completed.


Result:
Proceed to
NEXT



NEXT

END