Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › from 2016.05
RM19V0EQ _53 Suspension _014590 TIRE / WHEEL _0074031 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and proper inflation pressure.

Cold Tire Inflation Pressure:
for RHD
Tire Size Front Rear
215/60R16 95V 240 kPa (2.4 kgf/cm2, 35 psi)
215/55R17 94V 230 kPa (2.3 kgf/cm2, 33 psi)*1
240 kPa (2.4 kgf/cm2, 35 psi)*2
225/45R18 95W 250 kPa (2.5 kgf/cm2, 36 psi)

for LHD
Tire Size Front Rear
215/60R16 95V 210 kPa (2.1 kgf/cm2, 30 psi)
215/55R17 93V 220 kPa (2.2 kgf/cm2, 32 psi)


*1: for ASV50R-DETNKQ models

*2: except ASV50R-DETNKQ models

i.

Perform initialization (w/ Tire Pressure Warning System).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION


ii.

Tire pressure adjustment method when warm (w/ Tire Pressure Warning System):

1.

Turn the ignition switch off.

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON.

4.

Turn the GTS on.

5.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

6.

Adjust the tire pressure so that the displayed value is equal to the set pressure.

7.

Perform initialization and check that initialization completes.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION

8.

Check and record the value of the Data List item "Temperature in Tire". (Ts)

9.

Check and record the ambient temperature during tire pressure adjustment. (Tm)

10.

Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)

HINT:

Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P

P = (Specified Pressure) + (Ts - Tm)


11.

Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".


NOTICE:
for ECE-R64 Type:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.




b.
C137874

Using a dial indicator, check the runout of the tires.

Maximum Tire Runout:

1.4 mm (0.0551 in.)



Hide 2. ROTATE TIRES

a.
C143305C01
2.896,0.397 3.143,0.574 0.247,0.177 10 (A) 2.896,1.454 3.143,1.631 0.247,0.177 10 (B)
V100135

Front


If the spare tire uses a different type of wheel than the other tires, rotate the tires as shown by (A) in the illustration. If the spare tire has the same type of wheel as the other tires, rotate the tires, including the spare tire, as shown by (B) in the illustration.


Hide 3.INSPECT AND ADJUST WHEEL BALANCE

a.

Inspect and adjust the off-the-car balance.

i.

Steel wheel:

Maximum Wheel Imbalance:

8.0 g (0.0176 lb)



ii.
C144018N05
2.052,3.667 2.281,3.823 0.229,0.156 10 false (A)

Others (Non-steel wheel):

Maximum Wheel Imbalance:

8.0 g (0.0176 lb)


NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the adhesive surface of the tape.

·

Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.

Width (A):

25 mm (0.984 in.)


·

Push the balance weight securely with your finger to adhere it to the desired position.

·

Do not reuse balance weights.



HINT:

The inner side balance weight should be installed by clipping it to the rim.