DTC P0102 Mass or Volume Air Flow Circuit Low Input |
DTC P0103 Mass or Volume Air Flow Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0102 | The mass air flow meter sub-assembly voltage is less than 0.2 V for 3 seconds (1 trip detection logic). |
|
| P0103 | The mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic). |
|
| Mass Air Flow Rate (gm/sec) | Malfunction |
| Approximately 0.0 |
|
| 271.0 or more |
|
| Frequency of Operation | Continuous |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ OUTPUT DTC (DTC P0102 OR P0103) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0102 is output | A |
| DTC P0103 is output | B |
|
| ||||
| A | |
| 2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY) |
![]() |
Disconnect the mass air flow meter sub-assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-3 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Mass Air Flow Meter Sub-assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-5 (VG) - E83-118 (VG) | Always | Below 1 Ω |
| E14-4 (E2G) - E83-116 (E2G) | Always | Below 1 Ω |
| E14-5 (VG) or E83-118 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Inspect the mass air flow meter sub-assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter (Click here).
Inspect the mass air flow meter sub-assembly, referring to the Inspection for Mass Air Flow Meter (Click here).
Inspect the function of the mass air flow meter sub-assembly.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
Start the engine.
Check that the MAF value changes when the engine is raced.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND) |
Disconnect the mass air flow meter sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-4 (E2G) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-4 (E2G) - E83-116 (E2G) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY) |
Disconnect the mass air flow meter sub-assembly connector.
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-3 (+B) - 1A-8 | Always | Below 1 Ω |
| E14-3 (+B) or 1A-8 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||