ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) > Security Indicator Light Does not Blink |

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Immobiliser or Main Body / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Security Indicator | Security indicator light | ON/OFF | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Security Indicator | Security indicator light | ON/OFF | - |
| Result | Proceed to |
| Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test | A |
| B |
| C |
| Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK SECURITY INDICATOR LIGHT OPERATION |
When the immobiliser is set, check that the security indicator light blinks.*1
When the theft deterrent system is in the arming preparation state, check that the security indicator light on (Click here).*2
| Result | Proceed to |
| Both *1 and *2 are OK | A |
| *1 is NG (*2 is OK) | B |
| *2 is NG (*1 is OK) | C |
| Both *1 and *2 are NG | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - TRANSPONDER KEY ECU ASSEMBLY) |
Disconnect the security indicator light (heater control switch board) connector.
Disconnect the transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I19-8 (IND) - I56-1 (LP) | Always | Below 1 Ω |
| I19-8 (IND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
Disconnect the security indicator light (heater control switch board) connector.
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I12-22 (IND) - I56-1 (LP) | Always | Below 1 Ω |
| I12-22 (IND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR |
Disconnect the security indicator light (heater control switch board) connector.
Disconnect transponder key ECU assembly connector.
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I19-8 (IND) - I56-1 (LP) | Always | Below 1 Ω |
| I12-22 (IND) - I56-1 (LP) | Always | Below 1 Ω |
| I56-1 (LP) - Body ground | Always | 10 kΩ or higher |
| I56-6 (GND) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) |
Temporarily replace the security indicator light (heater control switch board) with a new or known good one (Click here).
When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.
|
| ||||
| OK | ||
| ||
| 7.REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Temporarily replace the transponder key ECU assembly with a new or known good one.
When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.
|
| ||||
| OK | ||
| ||