DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0705 | One of the following conditions A, B or C is met (2 trip detection logic): A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more: (a) Any 2 or more signals of the following are on simultaneously:
|
|
| Required Sensors/Components | Park/Neutral position switch assembly |
| Frequency of Operation | Continuous |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| DATA LIST |
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data.
Read the values displayed on the tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift SW Status (R Range) | Park/Neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (P Range) | Park/Neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (N Range) | Park/Neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (D Range) | Park/Neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Sports Mode Selection SW | Transmission control switch status: ON or OFF |
| - |
| 1.READ VALUE USING INTELLIGENT TESTER (NEUTRAL POSITION SW SIGNAL AND SHIFT SW STATUS) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Neutral Position SW Signal and Shift SW Status (R, P, N and D Range).
Read the values displayed on the tester.
| Tester Display | Shift Lever Position | Specified Condition |
| Neutral Position SW Signal | P or N | ON |
| Except P or N | OFF | |
| Shift SW Status (R Range) | R | ON |
| Except R | OFF | |
| Shift SW Status (P Range) | P | ON |
| Except P | OFF | |
| Shift SW Status (N Range) | N | ON |
| Except N | OFF | |
| Shift SW Status (D Range) | D or S | ON |
| Except D or S | OFF |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (SPORTS MODE SELECTION SW) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Sports Mode Selection SW.
Read the values displayed on the tester.
| Tester Display | Shift Lever Position | Specified Condition |
| Sports Mode Selection SW | S | ON |
| Except S | OFF |
|
| ||||
| OK | ||
| ||
| 3.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH) |
Inspect the transmission control switch .
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL SWITCH) |
![]() |
Disconnect the ECM connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Shift Lever Position | Switch Condition | Specified Condition |
| A25-37 (S) - Body ground | S, "+" or "-" | Engine switch on (IG) | 11 to 14 V |
| Not in S | Engine switch on (IG) | 0 to 1.5 V |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY) |
![]() |
Disconnect the park/neutral position switch assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E4-1 (RB) - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Park/Neutral Position Switch Assembly) |
|
| ||||
| OK | |
| 6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch assembly (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) |
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E4-7 (DL) - E26-69 (D) | Always | Below 1 Ω |
| E4-8 (NL) - E26-71 (N) | Always | Below 1 Ω |
| E4-2 (RL) - E26-68 (R) | Always | Below 1 Ω |
| E4-3 (PL) - E26-70 (P) | Always | Below 1 Ω |
| E4-4 (B) - E26-65 (NSW) | Always | Below 1 Ω |
| E4-7 (DL) or E26-69 (D) - Body ground | Always | 10 kΩ or higher |
| E4-8 (NL) or E26-71 (N) - Body ground | Always | 10 kΩ or higher |
| E4-2 (RL) or E26-68 (R) - Body ground | Always | 10 kΩ or higher |
| E4-3 (PL) or E26-70 (P) - Body ground | Always | 10 kΩ or higher |
| E4-4 (B) or E26-65 (NSW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||