STEERING COLUMN ASSEMBLY > INSTALLATION |
| 1. INSPECT STEERING COLUMN ASSEMBLY |
![]() |
Check that the 2 capsules are securely installed to the steering column assembly as shown in the illustration.
| A | B |
| 1 mm (0.0394 in.) | 12 mm (0.473 in.) |
| *1 | Capsule |
Check the 2 capsules for deformation and damage.
If either of the capsules is deformed, loose, missing or damaged, replace the electric power steering column sub-assembly with a new one.
| 2. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Install the steering intermediate shaft assembly to the steering column assembly.
| *a | Matchmark |
Install the bolt.
| 3. INSTALL STEERING POST ASSEMBLY |
Install the steering post assembly with the 4 nuts.
Install the ground wire with the bolt.
Engage the clamp.
Connect the 2 connectors.
Connect the connectors and engage the wire harness clamps to the steering post assembly.
| 4. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for LHD) |
Engage the clamp to install the No. 2 air duct sub-assembly.
Engage the 2 claws and guide.
| 5. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD) |
Engage the 2 claws to install the No. 2 air duct sub-assembly.
Install the bolt.
| 6. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Connect the steering intermediate shaft assembly to the steering link assembly.
| *a | Matchmark |
Install the bolt.
![]() |
Tighten the clamp.
| 7. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 8. INSTALL UPPER STEERING COLUMN COVER |
Engage the 2 claws to install the upper steering column cover.
Engage the 4 clips and 2 guides to the upper steering column cover.
| 9. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column) |
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Install the 2 screws.
![]() |
Engage the claw.
| 10. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column) |
![]() |
Engage the 2 claws to install the lower steering column cover.
![]() |
Install the 3 screws.
| 11. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
w/o Driver Side Knee Airbag:
Engage the 5 clips and 3 guides.
w/ Driver Side Knee Airbag:
Engage the 4 claws, 7 clips and 3 guides.
Install the instrument panel sub-assembly with the 2 bolts <B>.
| 12. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
| 13. INSTALL INSTRUMENT SIDE PANEL (w/o Driver Side Knee Airbag) |
Engage the 3 guides.
![]() |
Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
| 14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP (w/o Driver Side Knee Airbag) |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *1 | Alignment Mark (Yellow) |
| 15. INSTALL COWL SIDE TRIM SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the clip.
| 16. INSTALL FRONT DOOR SCUFF PLATE (w/o Driver Side Knee Airbag) |
Engage the 10 claws to install the front door scuff plate LH.
| 17. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
| 18. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD |
| 19. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Check if the spiral cable sub-assembly is centered.
![]() | Colored Part |
If the spiral cable sub-assembly is not centered, center it.
![]() |
While pushing on the interlock indicated in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.
![]() | Interlock |
![]() |
Rotate the spiral cable sub-assembly clockwise approximately 2.5 turns to the position where the colored part shown in the illustration is visible.
![]() | Colored Part |
![]() | Interlock |
| 20. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.
| *a | Matchmark |
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 21. INSPECT STEERING WHEEL CENTER POINT |
| 22. INSTALL HORN BUTTON ASSEMBLY |
| 23. INSTALL FRONT WHEEL LH |
| 24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column) |
| 25. TORQUE SENSOR ZERO POINT CALIBRATION |