Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > INITIALIZATION



PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

Necessary Procedures
Effect/Inoperative Function When Necessary Procedures are not Performed
See page
Correct the steering angle neutral point
Parking assist monitor system
Click here

NOTICE:
After the ignition switch is turned off, the navigation receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.


PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Replacement Part
Necessary Procedure
Effect/Inoperative Function when Necessary Procedures are not Performed
See page
ECM*1
Vehicle Identification Number (VIN) registration
MIL comes on
Click here
ECM
Code registration (Engine immobiliser system)
Engine start
See the Service Bulletin for the registration method.
  1. Throttle with motor body assembly
  2. Cleaning the deposits from the throttle with motor body assembly
  3. Engine assembly
  4. Cylinder head sub-assembly
  5. Camshaft
    (for intake or exhaust camshaft)
  6. Camshaft timing gear assembly
  7. Camshaft timing exhaust gear assembly
  8. Piston or piston ring
  9. Mass air flow meter sub-assembly
  10. Fuel injector assembly
  11. Fuel pump
  12. Air fuel ratio sensor
  13. Engine coolant temperature sensor
  14. Spark plug
  15. Ignition coil assembly
  16. Air leaks from intake system
  17. Gas leaks from exhaust system
  18. Knock control sensor
Inspection after repair
Poor idle, engine starting, etc
Click here for 2AR-FE
Click here for 2GR-FE
Automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into TCM
  3. Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Click here for U660E Initialization
Click here for U660E Registration
  1. Valve body assembly
  2. Shift solenoid valve SL3 and/or SL4
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Shift solenoid valve SL1 and/or SL2
Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
TCM (If possible, read the transaxle compensation code from the previous TCM)
Possible
  1. Reset memory
  2. Transfer transaxle compensation code
  3. Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Impossible
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow TCM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into ECM
  3. Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Click here for U760E Initialization
Click here for U760E Registration
  1. Valve body assembly
  2. Shift solenoid valve SL3 and/or SL4
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Shift solenoid valve SL1 and/or SL2
Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
ECM (If possible, read the transaxle compensation code from the previous ECM)
Possible
  1. Reset memory
  2. Transfer transaxle compensation code
  3. Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
Impossible
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn
  1. Large shift shock
  2. The deterioration of fuel efficiency
  1. ECM
  2. Automatic transaxle assembly
  3. Engine assembly
Reset memory
  1. Large shift shock
  2. The deterioration of fuel efficiency
Click here for U241E Initialization
Skid control ECU (Brake actuator assembly)
Perform system variant learning
  1. Slip indicator light illumination
  2. VSC disabled or malfunctioning
Click here
Power steering ECU assembly
  1. Torque sensor zero point calibration
  2. Assist map writing
  1. P/S warning light comes on
  2. EPS control
Click here
Electric power steering column sub-assembly
Torque sensor zero point calibration
Steering effort is different between turning steering wheel to left and right
  1. Spiral cable with sensor assembly
  2. Spiral cable sub-assembly
  3. Steering sensor
  1. Correct steering angle neutral point
  2. Steering angle setting
Parking assist monitor system
Click here for Initialization
Click here for Calibration
Navigation ECU sub-assembly
Navigation ECU sub-assembly initialization
Parking assist monitor system
  1. Rear television camera assembly
  2. Suspension, tires, etc.
Back camera position setting
Parking assist monitor system
  1. Certification ECU (smart key ECU assembly)*2
  2. ID code box (immobiliser code ECU)*2*6
  3. Steering lock ECU (steering lock actuator assembly)*2
  4. Telephone Transceiver Assembly*7
  5. Electrical key transmitter (key)*2
Code registration (Engine immobiliser system)
  1. Wireless door lock control system
  2. Smart entry and start system
  3. Engine start
  4. Steering lock system
See the Service Bulletin for the registration method.
  1. Transponder key ECU assembly*3
  2. Door control transmitter assembly*3
Code registration (Engine immobiliser system)
Engine start
See the Service Bulletin for the registration method.
  1. Door control transmitter*3
  2. Door control receiver*3
Code registration (Wireless door lock system)
Wireless door lock control system
Click here
Telephone Transceiver Assembly*7
Set the contract mode
Blocking system
-
  1. No. 1 air conditioning radiator damper servo sub-assembly
  2. No. 2 air conditioning radiator damper servo sub-assembly
  3. No. 3 air conditioning radiator damper servo sub-assembly*8
  4. No. 1 blower damper servo sub-assembly
Servo motor initialization (Air conditioning system)
DTCs are output
Click here
  1. Door window regulator assembly
  2. Power window regulator motor assembly
  3. Door glass
  4. Door glass run
Initialize power window control system
  1. Auto up/down function
  2. Jam protection function
  3. Operation function after ignition switch is turned off
  4. Key-linked function
  5. Wireless transmitter-linked function
Click here
  1. Sliding roof ECU (sliding roof drive gear sub-assembly)
  2. Sliding roof glass sub-assembly
  3. Sliding roof drive cable sub-assembly
Initialize sliding roof ECU (pulse sensor initial position setting)
  1. Automatic slide open/close and tilt up/down function of sliding roof
  2. Jam protection function
  3. Operation function after ignition switch is turned off
  4. Key-linked function
  5. Wireless transmitter-linked function
  6. Sliding roof open warning
Click here
  1. AFS ECU (headlight swivel ECU assembly)*4
  2. Rear height control sensor sub-assembly*4
Perform AFS ECU initialization
AFS function
Click here
  1. Headlight leveling ECU assembly*5
  2. Rear height control sensor sub-assembly*5
Perform Headlight leveling ECU initialization
Automatic headlight beam level control function
Click here
  1. *1: for Brazil OBD
  2. *2: w/ Smart Entry and Start System
  3. *3: w/o Smart Entry and Start System
  4. *4: w/ AFS (Adaptive Front-lighting System)
  5. *5: w/ Automatic Headlight Beam Level Control System
  6. *6: w/o Wireless Door Lock Buzzer Answer Back Function
  7. *7: w/ Blocking System
  8. *8: for 3 Zone Type