DTC P0340 Camshaft Position Sensor Circuit Malfunction |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
DTC P0345 Camshaft Position Sensor "A" Circuit (Bank 2) |
DTC P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) |
DTC P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 | One of the following conditions is met:
|
|
| P0342 P0347 | The output voltage of the VVT sensor is less than 0.3 V for 4 seconds (1 trip detection logic). |
|
| P0343 P0348 | The output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic). |
|
| P0345 | No VVT sensor signal at engine speed of 600 rpm or higher (1 trip detection logic). |
|
| Required Sensors/Components (Main) | VVT sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR INTAKE CAMSHAFT)) |
![]() |
Disconnect the VVT sensor (for intake camshaft) connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E54-3 (VC) - Body ground | Engine switch on (IG) | 4.5 to 5.5 V |
| E60-3 (VC) - Body ground | Engine switch on (IG) | 4.5 to 5.5 V |
| *1 | Bank 1 |
| *2 | Bank 2 |
| *a | Front view of wire harness connector (to VVT Sensor (for Intake Camshaft)) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM) |
Disconnect the VVT sensor (for intake camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E54-1 (VVR+) - E26-81 (VV1+) | Always | Below 1 Ω |
| E54-2 (VVR-) - E26-110 (VV1-) | Always | Below 1 Ω |
| E60-1 (VVL+) - E26-78 (VV2+) | Always | Below 1 Ω |
| E60-2 (VVL-) - E26-110 (VV1-) | Always | Below 1 Ω |
| E54-1 (VVR+) or E26-81 (VV1+) - Body ground | Always | 10 kΩ or higher |
| E54-2 (VVR-) or E26-110 (VV1-) - Body ground | Always | 10 kΩ or higher |
| E60-1 (VVL+) or E26-78 (VV2+) - Body ground | Always | 10 kΩ or higher |
| E60-2 (VVL-) or E26-110 (VV1-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT)) |
![]() |
Check the VVT sensor (for intake camshaft) installation.
|
| ||||
| OK | |
| 4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE) |
Inspect the teeth of the sensor plate.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
![]() |
Remove the cylinder head cover sub-assemblies RH and LH (Click here).
Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.
| *1 | Timing Mark |
|
| ||||
| OK | |
| 6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT) |
Replace the VVT sensor (for intake camshaft) (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0340, P0342, P0343, P0345, P0347 or P0348 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM) |
Disconnect the VVT sensor (for intake camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E54-3 (VC) - E26-111 (VCV1) | Always | Below 1 Ω |
| E60-3 (VC) - E26-111 (VCV1) | Always | Below 1 Ω |
| E54-3 (VC) or E26-111 (VCV1) - Body ground | Always | 10 kΩ or higher |
| E60-3 (VC) or E26-111 (VCV1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||