Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly (for driver door) is operated by the multiplex network master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

WIRING DIAGRAM


B234588E06


INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  2. If the power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (Click here).

1.READ VALUE USING INTELLIGENT TESTER (MAIN BODY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Communication D-Door Motor
    Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -
    Communication Master SW
    Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -

    OK:
    On the intelligent tester screen, OK is displayed.



NG
GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (D-DOOR MOTOR)
  1. Enter the following menus: Body / D-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver door power window manual up switch signal / ON or OFF
    ON: Driver door power window manual up switch operated
    OFF: Driver door power window manual up switch not operated
    -
    D Door P/W Down SW
    Driver door power window manual down switch signal / ON or OFF
    ON: Driver door power window manual down switch operated
    OFF: Driver door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (D-DOOR MOTOR)
  1. Enter the following menus: Body / D-Door Motor / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


    D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    OK:
    Driver door power window operates normally.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
  1. Disconnect the multiplex network master switch assembly connector.

  1. Disconnect the power window regulator motor assembly (for driver door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    K3-20 (UP) - K9-10 (UP)
    Always
    Below 1 Ω
    K3-15 (DOWN) - K9-7 (DOWN)
    Always
    Below 1 Ω
    K3-20 (UP) - Body ground
    Always
    10 kΩ or higher
    K3-15 (DOWN) - Body ground
    Always
    10 kΩ or higher
    K9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    K9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    J3-20 (UP) - J9-10 (UP)
    Always
    Below 1 Ω
    J3-15 (DOWN) - J9-7 (DOWN)
    Always
    Below 1 Ω
    J3-20 (UP) - Body ground
    Always
    10 kΩ or higher
    J3-15 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    J9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
  1. Replace the multiplex network master switch assembly (Click here).


NEXT


6.CHECK MANUAL UP / DOWN FUNCTION (FOR DRIVER DOOR)
  1. Check that the driver door power window moves when the manual up and down functions of the multiplex network master switch assembly are operated (Click here).

OK:
Driver door manual up and down functions are normal.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)
OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)