Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1249    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU receives stop light switch signals and uses them to determine whether or not the brakes are applied.
DTCs may be stored if one of the following occurs:
  1. Stop light switch stuck on malfunction.
  2. Accelerator and brake pedals depressed simultaneously.*

HINT:
*: The skid control ECU may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No.
DTC Detection Condition
Trouble Area
C1249
The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch is on for 60 seconds or more.
  1. STOP fuse
  2. Stop light switch assembly
  3. Stop light switch circuit
  4. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


C239818E03


INSPECTION PROCEDURE

1.CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION
  1. Interview the customer to check if the pedals were depressed simultaneously while driving or braking.

    OK:
    The pedals were not depressed simultaneously.

    HINT:
    The skid control ECU may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.
    If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.



NG
END
OK


2.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:

    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
Go to step 5
OK


3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays on or off according to brake pedal operation.



NG
Go to step 9
OK


4.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle and depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1249 is not output.
    A
    DTC C1249 is output.
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C173882E10
  1. Check that the STOP (7.5 A) fuse is normal.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A33-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6.INSPECT STOP LIGHT SWITCH ASSEMBLY


    C239673E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Stop Light Switch Assembly)



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C238832E13
  1. Reconnect the stop light switch assembly connector.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-30 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V*
    A49-30 (STP) - Body ground
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V

    HINT:
    *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK


8.RECONFIRM DTC
  1. Reconnect the skid control ECU connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle and depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1249 is not output.
    A
    DTC C1249 is output.
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)  

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C238832E13
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-30 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V*
    A49-30 (STP) - Body ground
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V

    HINT:
    *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)