DTC C1249 Open in Stop Light Switch Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1249 | The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch is on for 60 seconds or more. |
|

| 1.CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION |
Interview the customer to check if the pedals were depressed simultaneously while driving or braking.
|
| ||||
| OK | |
| 2.CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle and depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1249 is not output. | A |
| DTC C1249 is output. | B |
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL) |
![]() |
Check that the STOP (7.5 A) fuse is normal.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A33-2 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Stop Light Switch Assembly) |
|
| ||||
| OK | |
| 6.INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Switch pin free | Below 1 Ω |
| 1 - 2 | Switch pin pushed in | 10 kΩ or higher |
| *a | Component without harness connected (Stop Light Switch Assembly) |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
![]() |
Reconnect the stop light switch assembly connector.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| A49-30 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | |
| 8.RECONFIRM DTC |
Reconnect the skid control ECU connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle and depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1249 is not output. | A |
| DTC C1249 is output. | B |
|
| ||||
| A | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| A49-30 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | ||
| ||